No Nama Peralatan Rasio Deskripsi Merek Type Harga @
1 Heavy-Duty Diesel Engine Stand (Life Engine) 2 unit/ruang praktik "untuk pelajari mekanisme mesin diesel peralatan alat berat
Standard Equipment and Features
6-cyl.,4-stroke cycle diesel engine
Meets EPA 2010 emissions requirements
OEM ECM and wiring
VGT turbocharger
Cylinder range 8000 ~ 11000 cc
Direct Flow air filter
Air-to-air aftercooled
Radiator and cooling fan complete with protective guards
Fuel pedal
Tubular steel mounting frame
Heavy duty casters with 2 locking swivels
Diesel exhaust fluid (DEF) tank
12V batteries (2) w/plastic cases
Battery cut-off switch
Panic buttons (2)
Electronic programmable fault box (12 faults)
Dashboard including:
ECM and ATM breakout box
Ignition key switch w/test points
Gauges
ON/OFF switches
Selector switches
Indicator lamps
DLC using SAE J1939 protocols
Fully Functional OEM Vehicle Systems
High pressure common rail (HPCR) fuel injection system
PTO (power take-off)
Cummins diesel particulate filter (DPF)
Cooled exhaust gas recirculation (EGR) w/Selective catalytic reduction (SCR)
" RAKINDO RKN-8000 877.500.000
2 Starting & Charging System Trainer 2 unit/ruang praktik "untuk mempelejari sistem strater dan pengisian pada alat berat
Fully operational auto electrical trainer manufactured using original components.
Based on a generic auto electrical system, complete with charging, lighting, CB ignition systems and starter motor.
Components include: Alternator (motor driven), , Indicators, Brake lights, CB distributor (motor driven), HT ignition coil, 4x Spark plugs, Inertia starter motor, Start solenoid, Control dash panel, Relays and Battery isolator.
Variable speed control for alternator.
Rotating parts covered by mesh guards.
Board mounted in a vertical bench frame.
Powder coated paint finish.
Supply voltages, 240 volts AC and 12 volts DC.
" RAKINDO SCT-200AB 92.812.500
3 Lighting System Trainer 2 unit/ruang praktik "untuk mempelajari kelistrikan lampu penerangan pada alat berat
Most complete heavy vehicle lighting and accessory circuit trainer available; - Modular LED lights (except headlights) that match on-highway truck components; - Built to train up to four students at a time.
Manual fault box with 2 faults for the following Front Lights circuits: - Left headlamp ground circuit, - Left/right headlamp ground circuits;
Manual fault box with 10 faults for the following Lighting Switch Controls circuits: - Headlight switch (2), - Signal flasher (2), - Backup light switch, - Stop light switch, - Ignition switch, - Right turn signal indicator, - Relay No. 3, - Relay No. 4. Contents
Front Lights (1)
Lighting Switch Controls (1)
Rear Lights) (1)
Clearance Lights Kit (1)
Set of 89 jumper leads (1)
Stand with lockable storage box (1)
12VDC Power Supply (1)
" RAKINDO LST-100AB 75.937.500
4 A/C System Trainer 2 unit/ruang praktik "untuk mempelajari sistem kerja A/C pada alat berat
The simulator is able to train and exercise about automobile
air conditioning system, and understand how it works and faults, inspection.
Easy to demonstrate the training session in refrigerant cycle, heating,
air conditioning, temperatures and pressures.
It is the purpose to understand and diagnosis of air conditioning system
from faults in real vehicle effectively.
Charging system attached.
Compressor: 5HP motor, inverter RPM control type.
HFC-134a.
Specification
Composition : Compressor, condenser, dryer, expansion valve,
the orifice tube, the evaporator,Blowers, piping, cooling fans, the unit,
the control panel, Motor with speed control, pressure (high-1, low-3),
7 temperature gauge, etc
10 Fault insertion available
3 PCB board available to safety protection
PCB Board is connect PC with USB or RS 232
Size : Approx. 1,200 X 2,000 X 1,600 mm
Weight : Approx. 300 kg
Training Contents
Charging the refrigerant and recovery.
Air vent.
Session for FATC principles and theories, maintenance, inspection.
Made from new components
" YES01 YESA-4600 615.345.000
5 Steering & Power Steering System Trainer 1 unit/ruang praktik "untuk mempelajari sistem power steering pada alat berat
Overall bench adapt international standard square tube , angle iron seamless welding, after the surface polishing grinding, then the surface is dealt with high temperature spraying plastics , it can anti-corrosion and anti-aging , hardly lose it’s color, at the bottom of the bench is equipped with universal self-locking castor for mobile teaching .
Detection board adapt the pure aluminum-plastic panel, On the control panel with perceptual intuition hydraulic steering system schematic diagram, and the color is consistent with the original car control system ,and it is equipped with operation specification and experiment guidbook .
Adapt heavy-truck front overhang system and steering system assembly ,main configuration is auto tyre ,power steer ,steering wheel assembly, drum brake, shock absorber ,wheel bearing shell assembly , brake disc, etc.
Product function :
1.Three-phase/single motor simulation engine power. (220V/380V)
2.The layout is according to the auto actual structure and the requirement of assembly installation position .
3.It can carry on dismounting experiment , compare power steering with non power steering ,maintenance .
4.It’s equipped with oil pressure gauge ,display the steering pressure .
5.It can compare power steering with non power steering ,mobile universal wheel bench for moving conveniently .
Made from new components
" RAKINDO PST-100AB 143.437.500
6 Clutch Trainer 1 unit/ruang praktik "Untuk mengenal komponen dari kopling alat berat
An education unit of hydraulic clutch structure inside manual transmission.
Able to teach operation principle of hydraulic clutch effectively.
Paint for vehicle is used in painting and coating.
Each incised section is painted with different colors for education efficiency.
The entire process of ISO9001 and D.C.C.A.P.T of TQC method are applied in manufacturing.
Specification
Composition : Clutch pressing board, Clutch pedal, Clutch cylinder
Size : Approx. 400 X 300 X 300 mm
Weight : Approx. 20 kg
Made from new components
" RAKINDO CT-250AB 62.437.500
7 Differential And Axle Trainer 1 unit/ruang praktik "untuk mengetahui komponen differential dari alat berat
An educational unit for understanding the components of a heavy
equipment differential gear and training.
Is the best model to see operation state and location of differential
gear components by making parts which aren't seen at an actualone open.
Effective to educate the troubleshooting and inspection theory,training.
Each component is colored differently for educational effect.
It allows to see planetary gear directly on the wheel.
Specification
Composition : Large Heavy machinery differential gear
Stand : Steel frame with 5” lockable wheels
Size : approx. 2,000 X 800 X 500 mm
Weight : approx. 150 kg
Made from new components
" YES01 YESA-5200 391.410.000
8 Compressor AC (Cutting Section) 2 unit/ruang praktik "untuk mempelajari komponen kompressor A/C alat berat
An educational unit for the Air Conditioning Compressor Structure.
The equipment is proper to explain each parts and operating
principle of the compressor.
Each incised section is painted with different colors for education
efficiency.
The entire process of ISO9001 and D.C.C.A.P.T of TQC method of are applied in manufacturing.
Specification
Composition: Compressor
Size : Approx. 400 X 300 X 300mm
Weight : Approx. 20kg
- Made from new components
" YES01 YESA-2803 29.182.500
9 Alternator (Cutting Section) 2 unit/ruang praktik "untuk mempelajari kompenen alternator dari alat berat
An educational unit for the alternator.
The equipment is proper to explain each parts and operating principle of the alternator.
Painting and coating with Vehicle-Only materials.
Each incised section is painted with different colors for education
efficiency.
The entire process of ISO9001 and D.C.C.A.P.T of TQC method of are applied in manufacturing.
Specification
Composition : Alternator (Diesel vehicle type)
Size : Approx. 300 X 200 X 200 mm
Weight : Approx. 20 kg
Made from new components
" YES01 YESA-2710 31.719.000
10 Diesel Emission Tester (Smoke Tester) 1 unit/ruang praktik "untuk analisa hasil pembakaran engine pada alat berat,khususnya yang berbahan bakar diesel/solar
Real-time smoke measurement(%, k [m-1])
Portable and LED display
Outstanding accuracy, stability and durability
Response time of 0.5 second
Smoke, SOF measurement
Easy to use with handheld terminal
Built-in printer
RS232C PC program
RPM/ Oil temp. meter
Auto-Zero/ Span calibration function
Specification
Measuring items Smoke opacity ( %, k [m-1] )
RPM (option), °C (option)
Principle Light extinction method (Partial-flow sampling type)
Light source Green LED(565nm)
Shell length & Inside diam. Length: 215mm, Inside diameter: 21mm
Detector Photo diode
Range 0.0~100.0% (0.00~21.42m-1 )
Accuracy Less than 1%
Warm-up time 3~6 minutes
Display time 4 times /sec
Power 220V / 110V AC 50/60Hz
Temperature -10~40℃
Dimension 450(W) x 200(D) x 245(425)(H) mm
- Weight (Net/Gross) About approx.7kg / 11k
" KOENG OP-201 63.438.000
11 Standar Mechanical Tool Set 2 unit/ruang praktik "alat bantu bongkar pasang engine,transmisi,kelistrikan dll yang berhubungan dengan alat berat
Contains :
with 7 drawer cabinet with specification :
DRAWERS:
Inside dimensions:
approx. 5 drawers (H)75x(W)576x(D)380mm, max loading capacity:25KG. approx. 2 drawers (H)154x(W)576x(D)380mm Max loading capacity: 30KG. 100% ball bearing guide rails.
Patent design for locking system. consist of :
Drawer 1 contains : socket 8,10,11,12,13,14,16,17,18,19,20,21,22,23,24,27,30,32 mm ,flex handle 15 inc ,extension bar 5inc and 10inc universal joint ,bent handle ratchet ,sliding t-bar 10 inc ,adaptor 1/2x3/8M, 1/2x1/4M ,sparkplug socket 16mm,21mm ,13 Socket set sizes 6-22mm
extension bar: 3 "", 6"" ,T-handle 8 "" ,Flexible handle: 8 "" ,Universal Joint
Bent handle ratchet ,Adaptor : 3 / 8F x 1 / 4M .Weight: 1630g ,13 socket set 4 to 14mm ,Extension bar: 2 "", 4"" ,T-handle: 4 - 1/2 "" ,Flexible handle: 6 ""
Universal Joint ,Bent handle ratchet ,Weight: 690g
Drawer 2 contains : Combination wrench : 6 - 32 mm (21 pcs) ,75degree offset ring wrenches size : 8×9, 10×11, 12×13, 14×15,16×17, 18×19, 22×24mm
Drawer 3 contains : Combination plier-8"",Long nose plier-8"",Diagonal Cutting plier-8"",Water pump plier-10"",Slip-Joint jaw plier-8"" ,Ball head hex key set-Extra long type:1.5, 2, 2.5, 3, 4, 5, 6, 8, 10 ,Central Holed torqux key set - fully polished & satin plated:1.5, 2, 2.5, 3, 4, 5, 6, 8, 10
Heavy duty Impact bit:PH2-80mm(L) SL8-80mm(L),PH3-80mm(L) SL100-80mm(L)
External Straight Circlip Pliers-7"",Internal Straight Circlip Pliers-7"",External Bent Circlip Pliers-7"",Internal Bent Circlip Pliers-7"" ,weight : 850 gr
Drawer 4 contains :
Ball peen hammer-wooden shaft Adjustable wrench
5pc chisel & punch set Curved jaw locking plier-10"" Dead Blow Hammer
screwdriver (-) 0.8x4.5-100L , 1.2x6-150L , 1.6x8-200L , 1.2x6-38L
screwdriver (+) PH1-100L, PH2-150L, PH2-38, PH3-200L
Drawer 5 contains :
Double size flexible socket wrench: 8x10, 10x12, 12x14, 14x17, 17x19mm
1/2""Dr. E-socket: E10, E12, E14, E16, E18, E20
Flare Nut Wrench: 10x12mm
Deep socket: 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 23mm
32-494-920E-D
Torx bit socket: T15x55, T20x55, T25x55, T27x55, T30x55, T40x55, T40x55,T50x55, T55x55, T60x55, T70x55mm
Hex bit socket: H4x55, H5x55, H6x55, H7x55, H8x55, H10x55, H12x55, H14x55, H17x55mm
71pc bit socket set
Length-30mm:H5,H6,H7,H8,H10,H12mm,T20,T25,T30,T40,T45,T50,T55,M5,M6,M8,M10,M12mm
Length-75mm:H5,H6,H7,H8,H10,H12mm,T20,T25,T30,T40,T45,T50,T55,M5,M6,M8,M10,M12mm
Length-50mm:PH1,2,3,R0,1,2,T6,T7,T8,T9,T10,T15,T20,T25,T27,T30,H2,H2.5,H3,H4,H5 4,6,8 1,2,3 6,8,10
Bit adopter x 2Pcs: 1/ 2"",3/8"" x H10,Magnetic Screwdriver x 1Pcs
" SPERO 32-96-165 25.713.000
12 Electrical Tester (Oscilloscope) 1 unit/ruang praktik "untuk mengetahui volatge,arus serta grafik dari arus kelistrikan pada alat berat
Oscilloscope
HorizontalSample Rate 80 Ms/s (Dual CH Mode)20 Ms/s (Quad CH Mode)
Record Length 8192 in Dual CH Mode4096 in Quad CH Mode
Sample/Division 40Update Rate Real Time
Trig Mode Auto,Normal,Single Shot,Roll
Accuracy 0.01%Sweep Rate 500nS-200S in 1,2,5 2CH
sequential Range
VerticalBandwidth 20MHz
Resolution 12Bit
Channels QuadCoupling AC,DC
Input Impedance 1MΩ
Accuracy 3%
Max, Input Voltage DC or AC 200Vrms
Volt/Division 50mV to 50V in 1,2,5 in sequential range50mV to 50KV for Ignition Secondary
Trigger
Trigger source Internal, External
Coupling AC,DC
slope Rising Edge or Falling Edge,Trigger Sensitivity -100 ~100 Dvision
Others
Waveform Memory 256 Shots
- Ignition Analyzer Primary and Secondary Ignition, Conventional,DLI/DIS, Peak Voltage, Burn Time, Burn Voltage
" HANATECH HANASCOPE801 27.285.000
13 Heavy Duty Scanner (Heavy Duty Handheld Tester) 1 unit/ruang praktik "untuk mengetahui kinerja engine pada alat berat,truk baik mendeteksi kerusakan yang ada maupun menyajikan data secara live
Features
- Triple CPU High Performance Structure - Designed for fast boot-up and high performance by adopting - 3 CPUs dedicated to computing, communication and measurement for each - Wireless Connectivity - can access to the internet and utilize smart update, - quick feedback system, real-time PC interface, and direct printing
- Rechargeable Battery - 2100mAh Li-ion battery supplies power t for more than an hour under full load condition - without external source
- Diagnostic S/W Fully Compatible with the Scantool Unit
- 7” high resolution 1024 X 600 LCD ensures striking readability with striking graphical display of diagnostic data and information. - 16 GB SD Card memory - Win CE 6.0 Operating System
- Latest Windows CE 6.0 provides improved smart phone style user interface, better networking and enhanced system - security at the same time - Zero Second Boot-up
- Micro Controller Triple CPU Main control board ARM11 @ 600MHz
- Communication Board ARM9 @ 266MHz - Measurement Board (Optional) ARM9 @ 266MHz - System Memory Main Control Board NAND : Flash 128MB and SD RAM 256 MB - Main Control Board NAND : Flash 32MB and SD RAM 8Mb - Main Control Board NAND : Flash 32MB and SD RAM 8MB - External Memory 16GB SD Card
- LCD 7” TFT LCD (1024 X 600 pixel) - Input Devices Touch Screen - Power, Enter and ESC Keys - 4 way directional keys, F1 ~ F6 function keys - Indication Lamps 3 Color LED
- Sound Suzzer and speaker - Rechargeable Battery Li-lon Polymer 2100m Ah 1Cell
- Operating Voltage 7 ~ 35V DC (10~35V for charging)
- Housing Material PC + ABS resin with rubber shrouds
- Connectivity - Category Specifications
- External COM port 1 X USB 2.0 standard (master) + 1 X mini USB (slave)
- WiFi Module On-board - Blue Tooth On-board
- AC/DC Adapter - Category Specifications
- Input Power Vehicle Batery or 100 ~ 240V AC - Frequency 50 / 60 Hz
- Diagnostic Function - System and DTC Auto Search
- Favorite and Recent - Screen Capture and Memo - Full Text Description
- Smart Update - CAN Line Inspection
- Simple and easy menu structure - Utility Functions
- Dual Mode for Hyundai and Kia - Flight Record
- Basic Supplies - Base Unit - SD Card 16GB
- DLC Main Cable - SD Card Reader
- Self Test Adapter
- Quick Manual
- PC Utility CD (S/W)
- Parts included in the Asian Vehicles
- TOYOTA 17+1P Square
- TOYOTA 17P Round
- HONDA/ACURA 3P
- MAZDA 17P
- SUBARU 9P
- MITSUBISHI 12P+16P
- Kia 20P-A type Connector
- Kia 20P-B type Connector
- Hyundai & Kia Keyless Connector
- NISSAN 14P
- Ssangyong 14P
- Ssangyong 20P
- Daewoo 12P " XTOOL PS2-HEAVYDUTY 82.470.000
14 Air Compressor 1 unit/ruang praktik "untuk menghasilkan udara bertekanan yang dibutuhkan oleh peralatan peralatan pendukung pneumatic maupun simulator
Technical Data
Air Re-Tank 230 ℓ
Power 10 Hp 7.5(Kw)
3Φ/4P/380V
Cylinder Volume 1,717 cc
Displacement 1,173 ℓ/min
Type & Pulley Dia. approx.B2 & 505 mm
Motor Pulley Dia. approx. 203.2mm
Charging Time 230 ℓ/ 120 sec
Pump R.P.M 683
Working Pressure 6~8.5 Kgf/㎠
Weight 285 kg
Motor R.P.M 1,755
- Dimension approx. 1,575x565x1,135mm
" KOHANDS KC-802N 41.502.000
15 Clutch Cutting (Torque Converter) 1 unit/ruang praktik "untuk mempelajari komponen komponen dari torque converter pada alat berat
An educational unit for the Torque Convertor.
The equipment is proper to explain each parts and operating
principle of Torque Convertor.
Each incised section is painted with different colors for education
efficiency.
The entire process of ISO9001 and D.C.C.A.P.T of TQC method of are applied in manufacturing.
Specification
Composition : Torque converter (Cut away model)
Size : Approx. 400 X 300 X 300 mm
Weight : Approx. 20 kg
Made from new components
" YES01 YESA-2719 30.450.000
16 Basic Hydraulic Training System 1 unit/ruang praktik "untuk mempelajari dasar dasar hidrolik pada peralatan yang disematkan pada alat berat
Components specification 1. Hydraulic operation station It consists of aluminum material profile, and can be set up the system according to the different requirements, so it is easy to change the structure. Ambry that be made of special composite material is divided into the upper and lower levels, have their own independent lock system. The every component can be easily to storage. Work station equipped with loop work board and set oil pan to convenient for cleaning equipment. Four caster wheel with crack slot in order to move and install. Due to the point and height is adjustable, convenient for efficient experiment. Panel grooves gap is 25 mm, can easily move all kinds of components inserted on it. Experiment table dimension：approx.1600（length）×750（width）×1700（height） Aluminium panel dimension：approx. 1200（length）×750（width） Groove gap：25mm Aluminum wood cabinet：1 piece Caster with crack groove: 4 pieces Hydraulic Workbench ,Groove plate insert and extract system All components of the experiment system can be horizontal or vertical fixed in the same test bench aluminum mesa; operation is convenient and has very good endurance. 2. Hydraulic components
Configuration industry use hydraulic valve, the greatest work pressure is 31.5 Mpa.Each hydraulic component equip with oil-way transition bottom board, can easily andcasually laid on the panel. Oil-way lap joints use the open closed quick changeconnector, dismantle and connect easily, not leak oil. a) Work power: AC：380V b) Frequency ：50Hz/60 Hz c) Safety rate-limiting range：1000-1500 r/min d) Power ：1.1KW e) Flow ：6L/min Noise far away hydraulic table 1.5m when hydraulic pump working≤58dB Demonstrative experiment oil-way liquid flow require pressure only is 4-6Mpa Use gear pump system （1） Motor-pump set Use pump open shelf installation, structure compact, low noise, easy to maintenance; （2）oil box：nominal volume 35L；accompany oil temperature liquidometer airfilter.etc. 4. Electrical control module: Power module：With three phrase leakage protection, provide effective protection for pump station safety work; Whole power jack use socket with jacket protection. Improve safety precautions effectively.IV. Training contents: 1. Directional control circuit, a) Inverting circuit of hand shuttle valve
2. Pressure control circuit
a) Single grade pressure regulating circuit
b) Secondary level pressure regulating
c) The unloading circuit using “M” type manual shuttle valves
d) The unloading circuit using the relief valve
e) The balance circuit using sequence valve
f) Level 2 pressure circuit
3. The flow speed circuit using for throttle valve
a) Enter oil-way throttle speed regulation
b) Back oil-way throttle speed regulation
c) Side oil-way throttle speed regulation
4. Speed regulation circuit using for speed regulation valve
a) Enter oil-way throttle speed regulation
b) Back oil-way throttle speed regulation
c) Side oil-way throttle speed regulation
5. Sequence action circuit using for sequence valve
6. One-way interlock circuit use hydraulic control one-way valve
7. Locking circuit use o type manual shuttle valve
8. The speed interchange circuit of flow valve short circuit
9. Pressure distance adjustment circuit
10. The other circuit design by themselves
" DOLANG DLYY-DH101 539.220.000
17 Crane 5 ton 1 unit/ruang praktik "alat angkat komponen alat berat untuk benda berat
Operates like an arm in a work area, where it can function as a manipulator for positioning tasks
A hoist is attached to the arm for lifting
Arm mounted on the wall or attached to a floor mounted support
Arm can rotate 360° or 180 °
The hoist can move along the arm
Parameter:
Lifting weight 5 tons
Lifting height 4.5 m
Valid radius 5 m
Working system A3
Hoisting speed Slow speed m/min 0.8
Normal speed 8 m/min
Slewing speed 0.5-1 m/min
Circulate speed 20 m/min
Slewing angle 180/270/360/etc
Max. height 6.5 m
Max. length 5.9 m
Total weight approx. 4224 kg
" KERNEL JC-75 (5TON) 412.344.000
18 Hydraulic Excavator Trainer 1 unit/ruang praktik "untuk mempelajari cara kerja sistem kerja hidrolik pada excavator dan fungsi fungsi perintah yang ada serta komponen komponennya
An educational unit for understanding the components of the Excavator
hydraulic system and training.
Is the best model to see operation state and location of components by
making parts which aren't seen at an actual one open.
Effective to educate the troubleshooting and inspection theory/training.
Specification
Composition : Battery, operating lever, light system, horn, hydraulic lever,
instrument panel, starter motor, battery connector, relay, digital meters, etc
Kubota U17 mini excavator hydraulics
Three-phase 380V 7.5 horsepower motor
Hydraulic tank 20 liters
5” 4 wheels on the frame
Hydraulic cylinder mounted - Fix to the bottom by hydraulic cylinder
during operation
Size : approx. 2,700 X 1,300 X 2,000 mm
Weight : approx. 450 kg
Training Contents
Operating an excavator.
Hydraulic line inspection/check.
" YES01 YESA-5104 1.748.338.500
19 4 Dial Pressure Gauge (Quadrigage) 2 unit/ruang praktik "untuk mengukur tekanan oli hidrolik pada alat berat secara bersamaan
Perform four gauge functions
Case is dust and moisture resistant
Glycerin filled models dampen pointer vibration and provided for extended life.
Compact for tool box storage
Available with 12 or 36 inch pressure hoses and1/8 inch NPTF male fitting
Includes bleeder screw and convenient hanger
Built-in pressure sensor protects low range gauges from high pressure
Compatible with most hydraulic fluids
Standard Gauge
Read in lb/in2 (PSIG) and kg/cm2. Measures 6 7/16 inch diameter. 3000 PSIG or 5000
PSIG maximum pressures
" MICO Quadrigage™ (80-740-001) 25.375.500
20 Excavator Electric Circuit Training Simulator 1 unit/ruang praktik "untuk mempelajari sirkut kelistrikan pada excavator
An educational unit for understanding the components of the excavator
and training.
Is the best model to see operation state and location of components by
making parts which aren't seen at an actual one open.
Effective to educate the troubleshooting and inspection theory/training.
Specification
Composition : Battery, Operating Lever, Light System, Horn, Hydraulic Lever,
Instrument Panel, Starter Motor, Battery Connector, Relay, Digital Meters, Etc
Electronic systems using a Hyundai/level heavy machinery excavator 555-7K
Size : Approx. 2,000 X 600 X 1,700 mm
Training Contents
Measuring the input/output data in each component.
Made from new components
" YES01 YESA-5101 1.062.579.000
21 Wheel Loader Electric Circuit Training Simulator 1 unit/ruang praktik "untuk mempelajari sirkuit kelistrikan dari wheel loader
An educational unit for understanding the components of the Electric Forklift electric system and training.
Is the best model to see operation state and location of components by making parts which aren't seen at an actual one open.
Effective to educate the troubleshooting and inspection theory, training.
Specification
Composition : ECU, Battery, operating lever, light system, horn, hydraulic lever,
starter motor, battery connector, relay, digital meters, power DC 24V battery,
2 A meter, 2Vmeter
Electric circuit equipment using Hyundai /level Heavy machinery wheel loader
Size : approx. 2,000 X 600 X 1,700 mm
Weight : approx. 350 kg
Training Contents
Replacement of the Timing Belt and other various belts, Belt Tension Control.
How to replace Break Disk and Pad.
How to replace break oil and remove the air.
How to attach, detach the Cylinder Head.
How to attach, detach the Generator and Start Motor.
Made from new components
" YES01 YESA-5102 1.164.079.500
22 Electric Forklift Circuit Training Simulator 1 unit/ruang praktik "untuk mempelajari sirkuit kelistrikan dari forklift elektrik
An educational unit for understanding the components of the Electric Forklift
electric system and training.
Is the best model to see operation state and location of components by making
parts which aren't seen at an actual one open.
Effective to educate the troubleshooting and inspection theory, training.
Specification
Composition : Battery, operating lever, light system, horn, hydraulic lever,
instrument panel, starter motor, battery connector, relay, digital meters, etc
Electrical circuit device of left-seat type Electric Forklift
Voltage, current measurement of driven rotor and hydraulic rotor during operation
Size: approx. 2,000 X 600 X 1,700 mm
Weight: approx. 350kg
Training Contents
Measuring the input/output data in each component.
Made from new components
" YES01 YESA-5103 1.021.978.500
23 Excavator Training Simulator 1 unit/ruang praktik "untuk pelatihan penggunaan excavator
Software Warranty Free Update for Lifetime
Support Language English or Customized
Voltage 110V-220V
Output Power 300-400W
Features:
1. Real machine hardware copy PRO rata
2. Strong sense of simulation
3. Simple but not easy
4. Considerable price performance
5. Strong applicability
6. Small volume, easy to place
Inside Software system features:
1, Operation and skill training
2, Usual work scenes training
3, Machinery structure teaching
4, Safety consciousness training
Made from new components
" HISOFT HL-ES-A 475.782.000
24 Wheel Loader Training Simulator 1 unit/ruang praktik "untuk pelatihan penggunaan wheel loader
features:
1. Reduce the training cycle ad time
2. Non dangerand accident training
3. Strong sense of simulation
4. Simplify training course and improve effiency
Inside software system features:
1. Operation and skill training
2. Usual work scences training
3. Machinery structure teaching
4. Safty consciousness training
Gross Weight:145kg
Supported Language:English etc.
Voltage:210-230V
Packaging Size:136x86x126cm
Displayer Size:27 inches or customized
Warranty:One year
Output power:300-400W
Made from new component
" HISOFT HL-LS-A 475.782.000
25 Forklift Training Simulator 1 unit/ruang praktik "untuk pelatihan penggunaan forklift
From the angle of students:
1, Simulator stands for the newest training method and tendency
2, The trainees will be interested with the new training equipment
3, It will make the Admissions and training easier
4, Simulator will help the trainees get much more familiar with the real machine before operating it.
5, Simulator will enhance the teaching strength and promote the company image
From the angle of trainees:
1, Simulator will help them learn faster and better than before
2, Simulator will increase the interest during the training course
3, Simulator will make the course be interesting
4, If the weather were bad, the trainees could still continue their training via the simulator
1, Reduce the training cycle and time2, Non danger and accident training
3, Strong sense of simulation4, Simplify training course and improve efficiency
Inside Software system features:
1, Operation and skill training 2, Usual work scenes training
3, Machinery structure teaching 4, Safty consciousness training
Gross Weight:145kg
Supported Language:English etc.
Voltage:210-230V,Packaging Size approx. :136x86x126cm
Displayer Size:27 inches or customized
Warranty:One year,Output power:300-400W
Made from new component
" HISOFT HL-FS-A 475.782.000
26 CRDI Engine Injection Control System with auto fault 1 unit/ruang praktik "untuk mempelajari cara kerja sistem injeksi bahan bakar diesel yang dikontrol oleh computer (ECU) beserta troubleshootingnya
Composition
- CRDI Diesel engine injection - Includes all components used in the CRDI injection - Displays fuel delivery cycle from tank to tube (tester) and all sensors
related diesel injection circuit
- Configuration: operation key, voltage display, LED indicators for failure,
a fuse box for all parts of fuel pumps, fuel tank, ECU, an injector, a fan,
a crank gear, the cam gear and the tester for displaying the fuel injection
- Measure voltage of resistance and all of the sensor (camshaft sensor and
the crankshaft sensor, oxygen sensor, the air inlet sensor, a temperature sensor,
a water temperature sensor) by using multimeter- All circuits for the electronic control ECU- Sensor measurements: temperature sensor, oxygen sensor, air flow sensor, air temperature sensor, an engine temperature sensor, exhaust gas sensor, crank sensor and a cam sensor
- power supply : 220V- DC12V- LED Fault indicate sensor can be measured by multimeter- Stand with wheel
Auto Fault Function
Cabinet Type storage space with 2 door
Size : Approx. 1,300 X 600 X 1,600 mm
Weight : Approx. 100 kg, key box
Training Contents
Measure the waveforms and check the changes according to RPM speed.
Engine operation : check the operation of the injector and sparks in the order
of switch plugs (1, 3, 4, 2) and inspect whether normal operation of each sensor." YES01 YESA-4241 428.203.500
27 Commonrail Diesel Test Bench 1 unit/ruang praktik "untuk kalibrasi dan analisa injector diesel yang sudah dikontrol oleh komputer, dan mengkalibrasi sesuai dengan standar bawaan pabrik
1,Pump testing: pump delivery, pressure,PVC working status, leakage of itself,
2,Injector testing: leakage, injection oil quantity and back oil quantity(pre-injection,Idling, emissions, full load)
3,it can test pressure sensor,and DRV valve
4. Supports system: BOSCH,DELPHI,DENSO,SIEMENS and commonly used in Indonesia
5. Testing data inside( pump and injector)
6. Electronic fuel delivery measuring, automatic detection.
Technical parameters
1.Motor power: 7.5KW
2. Electronic power: 3 PHASE 380V or 1 PHASE 220V
3. Motor speed: 0-4000RPM
4. Presure adjustment: 0-2000bar
5. Flow testing range: 0-600ml/1000times
6.Flow measurement accuracy:0.1ml
7. Temperature range: 40+-2
8. Cooling system: fan or forced cooling" KERNEL CR3000-708A 416.500.500
28 Common Rail Diesel Injector Return Flow Tester 3 unit/ruang praktik "Alat uji yang digunakan untuk memantau perbandingan pengembalian bahan bakar Diesel pada sistem diesel commonrail antara masing-masing injektor individu, dan memantau hingga 6 aliran injektor sekaligus
All adaptors are individually located in a sturdy carry case which also includes fuel resistant easy to read calibration tubes / containers and flexible hoses.
Up to 6 cylinders measured simultaneously
Includes comprehensive quick connect fittings
Includes blank off tubes and pinch off pliers
Contains measurement tubes for short term test (crank only condition) and bottles for more accurate long term tests.
Includes adapters suitable for Bosch, Denso, Delphi, Siemens/VDO systems,Dimensions
Length: approx.450mm
Width: approx. 320mm
Height: approx. 60mm
Weight: approx. 1.63kg" KERNEL CRT028 4.758.000
29 Electronic EGR, Throttle Body & Actuator Tester 4 unit/ruang praktik "Alat Uji untuk mendiagnosa performa dari EGR (katup gas elektrik),dan sensor utama pada diesel commonrail
Electronic EGR - Also allows for the EGR position sensor to be tested during EGR actuator operation.
Electronic Throttle Body – This also allows for the integrated TPS units to be tested during the throttle body operation.
Variable Intake Manifold Actuator
Intake Air Control (IAC) Actuators -both on and off the vehicle
Supply Pump - for direct fuel injection and common rail diesel systems. Must not be operated dry.Electric Control Regulators - for direct fuel injection and common rail diesel systems.EVAP Control Solenoids -both on and off the vehicle
Cooling Fans -testing at varying speeds
HVAC Blower Motors / Blend Doors -both on and off the vehicle
Other actuators and motors -that can be operated by PWM or DC within the current range.Power Supply: 11 - 18 VDC
Output Current: 0 - 40A (high side/low side drive)
Current Display: 0 - 40A (0.1A resolution)
PWM Rate: 15kHzPWM Range: 0 - 100% duty
Over Temperature: Heat Sink > 120° F (output disabled)
Over Current: > 40A (output disabled)Continuous On Time: 2 minutes @ 40 amps, 10 minutes @ 20 amps, 25 minutes @ 10amps, 30 minutes @ 5 amps.
Kit includes:
1 x Tester with 7ft (2.1m) cables,2 x 3ft (0.91m) 40A Test Leads
2 x Battery Clips,2 x Alligator Clips,2 x Female Spade Probes,1 x Male Spade Probe
Dimensions:
Length: approx.260mm,Width: approx. 220mm,Height: approx.80mm
Weight: approx.0.8 kg" Plus Equip EQP-115 28.230.000
30 Heavy Duty Battery Charger 2 unit/ruang praktik "untuk mengisi kembali tenaga aki yang sudah lemah dan membantu memperkuat daya aki saat mengalami kesulitan dalam menstarter mobil
INPUT VOLTAGE 1PH220V/380V
FREQUENCY 50/60Hz
INPUT POWER 4.5/40KVA
STARTING VOLTAGE 12/24V
STARTING CURRENT 1800A
CHARGING VOLTAGE 10-15/20-30V
CHARGING CURRENT 100A
DIMENSIONS（LxWxH)approx. 350x340x820mm
WEIGHT approx. 42KG
Accessories included:
BATTERY CLAMP 2PCS,CASTOR 2PCS,CASTOR AXLE 1PC
COTTER PIN 2PCS,OUTPUT CABLE 2PCS,HOST 1PC
INSTRUCTIONS 1PC,WARRANTY CARD 1PC" SHUGUANG 1800A 15.859.500
1.11.3 TEKNIK ALAT BERAT
No Nama Peralatan Merek Type Harga @
1 Heavy-Duty Diesel Engine Stand (Life Engine) RAKINDO RKN-8000 877.500.000
2 Starting & Charging System Trainer RAKINDO SCT-200AB 92.812.500
3 Lighting System Trainer RAKINDO LST-100AB 75.937.500
4 A/C System Trainer YES01 YESA-4600 615.345.000
5 Steering & Power Steering System Trainer RAKINDO PST-100AB 143.437.500
6 Clutch Trainer RAKINDO CT-250AB 62.437.500
7 Differential And Axle Trainer YES01 YESA-5200 391.410.000
8 Compressor AC (Cutting Section) YES01 YESA-2803 29.182.500
9 Alternator (Cutting Section) YES01 YESA-2710 31.719.000
10 Diesel Emission Tester (Smoke Tester) KOENG OP-201 63.438.000
11 Standar Mechanical Tool Set SPERO 32-96-165 25.713.000
12 Electrical Tester (Oscilloscope) Hantek 6074BE 27.285.000
13 Heavy Duty Scanner (Heavy Duty Handheld Tester) XTOOL PS2-HEAVYDUTY 82.470.000
14 Air Compressor KOHANDS KC-802N 41.502.000
15 Clutch Cutting (Torque Converter) YES01 YESA-2719 30.450.000
16 Basic Hydraulic Training System SSEDU ZMH1107T 539.220.000
17 Crane 5 ton KERNEL JC-75 (5TON) 412.344.000
18 Hydraulic Excavator Trainer YES01 YESA-5104 1.748.338.500
19 4 Dial Pressure Gauge (Quadrigage) MICO Quadrigage™ (80-740-001) 25.375.500
20 Excavator Electric Circuit Training Simulator YES01 YESA-5101 1.062.579.000
21 Wheel Loader Electric Circuit Training Simulator YES01 YESA-5102 1.164.079.500
22 Electric Forklift Circuit Training Simulator YES01 YESA-5103 1.021.978.500
23 Excavator Training Simulator HISOFT HL-ES-A 475.782.000
24 Wheel Loader Training Simulator HISOFT HL-LS-A 475.782.000
25 Forklift Training Simulator HISOFT HL-FS-A 475.782.000
26 CRDI Engine Injection Control System with auto fault YES01 YESA-4241 428.203.500
27 Commonrail Diesel Test Bench KERNEL CR3000-708A 416.500.500
28 Common Rail Diesel Injector Return Flow Tester KERNEL CRT028 4.758.000
29 Electronic EGR, Throttle Body & Actuator Tester Plus Equip EQP-115 28.230.000
30 Heavy Duty Battery Charger SHUGUANG 1800A 15.859.500
Untuk
pemesanan atau informasi silahkan hubungi alamat kontak kami :
CV.ASAKA PRIMA | DUTA MEDIA GROUP.
PERCETAKAN & DISTRIBUTOR ALAT LAB & PERAGA PENDIDIKAN.
Jl.Maulana Hasanudin No.52 Cipondoh - Kota Tangerang
PERCETAKAN & DISTRIBUTOR ALAT LAB & PERAGA PENDIDIKAN.
Jl.Maulana Hasanudin No.52 Cipondoh - Kota Tangerang
Cabang : Ruko Pondok Permata No.1, Jl.
Raya Tanggul, Rajeg Mulya, Rajeg, Tangerang, Banten 15540
021 5570 1397
021 5570 2265
0813.1019.7873
WA.0812.1236.8589
WA.0877.7432.4146
0813.8053.7399
www.asakaprima.net
asakaprima@gmail.com
021 5570 1397
021 5570 2265
0813.1019.7873
WA.0812.1236.8589
WA.0877.7432.4146
0813.8053.7399
www.asakaprima.net
asakaprima@gmail.com
