ALAT SMK 2018, Kompetensi Keahlian Teknika Kapal Niaga , Alat prkatek SMK Teknika Kapal Niaga 2018,ALAT PERAGA SMK 2019,ALAT PERAGA SMK 2018
Kompetensi Keahlian Teknika Kapal Niaga
No Nama Alat Deskripsi Merk Tipe Qty Harga Satuan
1 Engine Room Simulator Digunakan untuk pengenalan mengenai ruang mesin pada kapal, sistem pendingin, sistem mesin bantu,dan kelistrikan. TRANSAS 1 30.000.000.000
- Configured with realistic consoles and several large monitor so to reproduce the ER different
areas.
- Engine
• Low Speed diesel, with CPP or FPP, with conventional or electronic control
• Medium Speed diesel,
• Medium Speed diesel, up to 4 engines, gear and CPP
• Steam turbine, with FPP
• Gas turbine, with CPP
• All related auxiliary equipment (electricity generation, Sea water cooling, Lubricating oil etc as below specified)
- AuxiliAry system
• Air Conditioning and refrigeration Plant
• Power Plant
• Treatment Plant (separators, reverse osmosis system, etc.)
• Freshwater plant
• Marine equipment (Compressors, pumps,
2 Motor Diesel Digunakan untuk mengenal jenis-jenis penggerak motor pada mesin kapal DEUTZ MB-DY200 1 1.177.789.500
DEUTZ Generator Set
Generator Model MB-DY200
Prime Power 200KW/250KV
Power Factor COSΦ=0.8
Genset Weight 2300KG
Dimensions(L×W×H) 1800mm×650mm×1450mm
Rated Voltage 400/230V
Rated Frequency 50Hz
Diesel Engine
Brand Deutz
Engine Model TD226B-4D
Rotating Speed 1500RPM
Power 66KW/82.5KVA
Fuel Consumption at 100% Load ≤209g/kw.h
Total Lubrication System Capacity 38L
Bore×Stroke 105×120 mm
Compression Ratio 15.5 : 1
Displacement 4.16L
Engine Structure 4 Cylinder,4 Stroke
Cooling System Forced Water Cooling Cycle
Governing system Mechanical Governor/ Electronic Governor(Option)
Starting Method 24V Electrical starting
Engine Filtration System Dry Air Filter,Fuel Filter,Engine oil Filter
3 Motor Bensin Digunakan untuk mengenal jenis-jenis penggerak motor pada mesin kapal PARSUN F40BWS-T-EFI 1 235.500.000
40HP EFI outboard specification:
Engine type 4-stroke,3-cylinders, OHC
Displacement 747 cc
Bore x Stroke mm(in.) 65.0×75.0(2.56×2.95)
Max output Kw(HP)@ r/min 29.4(40)@5000
Fuel induction system Electric Fuel Injection
Ignition system Micro Computer
Starting system Manual / Manual + Electric
Steering system Tiller handle
Gear shift Forward-Neutral-Reverse
Gear ratio 2.0(26/13)
Trim and tilt system Power trim&tilt
Max fuel consumption 13.8 L/h
Fuel tank capacity 24L
Sump oil capacity 1:07
Gear oil capacity 430cc
Dry weight 92.4kg~101.5kg
Alternator output 12V 200W
Recommended transom height 381mm (15 in.)
4 Insatalasi Poros Baling-baling Digunakan untuk pengenalan cara kerja sistem baling-baling pada kapal -
Length: 900–2000 mm
Input power: 200 – 2000 hp Input speed: 2500 – 3600 rpm Steering angle: 35 – 40 degree trim angle: 15 degree
weight: 70 – 700
body material: SS
5 Basic Electronics Trainer Digunakan sebagai perangkat untuk menjelaskan elektronik dasar. SSEDU ZE1110 1 31.719.000
I. Technical parameter:
1. Power
Input: AC220V±10%
Output:(1)DCV ,±12V/0.2A,DCI≥0.2A(2)DCV,±5V/2A,DCI≥1A
2. Signal source
(1)function generator
output wave shape: Square wave triangle wave sine wave
Amplitude: square wave triangle wave sine wave : (0 ~ 10 V for peak-peak)
Frequency range: it can be divided to 4 range: 0HZ~200HZ, 200HZ~10KHZ, 10KHZ~100KHZ, 100KHZ~200KHZ
(2)DC signal, double way, ±5V, ±0.5V, it can be adjust continuously
3. supply 4 single pulse generator
4. Four ways (T1, T2, T3, T4) sequence generator, and start and stop circuit
5. 1HZ~10MHZ pulse output
6. 12 ways switch output display circuit
7. 6 bits 7 segment LED displayer
8. 2 ways BCD code switch
9. The system has many 8P~40P common round hole, IC experiment circuit plug and socket, with resistor for 1K, 10K, 22K, 100K, 680K etc. and contact safety socket, it can connect resistor, capacitor, it can do pulse experiment, digital circuit experiment, logic circuit and many basic experiment.
10. 555 timer base circuit with audio output control
11. Six high precision digital frequency meter, test range: 0-9.9999MHZ error range: <1HZ(it is designed by CPLD chip)
12. Supply with 3 and a half digital voltage meter
13. It has potentiometer group and resistance capacitance and inductance diode electronic component, and easy for students to use.
14. Analogue circuit experiment zone is made of single pipe two pipe differential amplifiers and integrated op-amp rectifier voltage filter of circuits, etc
15. Experiment area use metal needle, use a medium sized hole, never oxidation, beautiful and beautiful, practical strong, experiment with wires plug metal paint process, inserted more convenient, more reliable contact, and long service life
II. Experiment content
Digital part experiment contain:
1.TTL logical gate parameters test and use
2.CMOS Integration logic gate of the test
3.Gate circuit logic function test
4.Common combination logic function components test
5.Data collect and application
6.Blood type relationship detection circuit and voting circuit
7.RS function of the trigger and test
8.JK trigger logic function and main parameters test
9.The shift register function test
10.Decade computer(CMOS)
11.Asynchronous counter
12.Synchronous counter
13.Count decode display circuit experiment
14.555 Integrated timer and application
15.Sequential detector
16.Follow type is A/D conversion circuit
17.Artificial control traffic light controller
18.Automobile tail light control circuit
19.Digital circuit design
20.Timing circuit testing and research
21. Wave shape generate and monostable trigger
22. A/D convert circuit
23. D/A convert circuit
Analog part experimental contents:
1, Rectifier voltage filter and parallel circuit
2, Series voltage stabilizing circuit
3, Integrated voltage stabilizing circuit
4, Integrated power amplifier
5, Complementary symmetry power amplifier
With bread board and expand chip
6 MCU Training Set Digunakan sebagai perangkat untuk pelatihan/percobaan tentang micro computer dasar. CHOIEO 66968201 1 138.000.000
Features
• This trainer adopts modular and open type design, each module can be used separately for basic experiment or combined for training experiment and course design.
• The training table is designed with drawer cabinet for module storage and four lockable universal caster wheels for easy movement. When doing experiment, the top surface of table can be folded so that students can put modules on base plate to conduct training. The table can also be used as a normal desk when the top surface is closed.
• The modules use high strength PCB as the carrier, the front side is printed with terminal signals and equipped with main components, the wiring is conducted on the back side.
• It covers various microcontroller training courses, such as I/O training, A/D training, D/A training, LED/LCD dot matrix module experiment, motor control, etc. Besides, mechatronics application can be extended on this trainer by adding an intelligent material handling device.
TRAINING CONTENT
• Lights flash training
• Marquee’s training
• Independent key input training
• Photoelectric isolation input and output training
• Metal detection training
• Dynamic nixie tube display training
• Matrix keyboard interface training
• Relay isolation control training
• Buzzer playing training
• The expansion of IO port with 8255 chip training
• 1602 liquid crystal display module control training
• 128*64 LCD module control training
• Dot matrix LED screen character display training
• AD conversion training
• DA conversion training
• LM35 temperature sensor acquisition training
• Single bus temperature sensor acquisition training
• The control of AC/DC gear motor training
• Open loop control of step motor training
• RS232 communication training
TECHNICAL PARAMETERS
1. Power input: AC220V±10% (safety plug output, with leakage protection function)
2. Output voltage: (DC±12V±5%, 1A); (DC±5V±5%, 1A); (DC24V±5%, 1.5A)
3. Working environment: temperature -10ºC~+40ºC, relative humidity
BASIC CONFIGURATION
1. Training table /Worktable
(1) Powder coating steel frame
(2) Foldable table face
(3) Storage cabinets
(4) Universal lockable wheels
2. Power module
(1) Switch: leakage protector, rocker switch
(2) Power supply: ±12V, +24V, ±5V, AC220V
(3) Switching power supply 2 units
(4) Power indicator and safety sockets
(5) Module size: 290mm×285mm×100mm
3. Mainframe module
(1) Integrated chip: ATMEGA48-10PU, AT89S52
(2) Pin header: 1×40 with locking mechanism
(3) Dial switch 4T, active buzzer
(4) A type USB jack and D type DB232-9T curved needle
(5) Interface: RS232, on-system download interface
(6) Module size: 290mm×150mm×150mm
4. Emulator module
(1) 51 microcontroller emulator
(2) Power supply interface
(3) USB interface
(4) Emulator interface
(5) Module size: 290mm×150mm×150mm
5. LCD module
(1) 128×64 Graphic Type LCD
(2) 1602 character type LCD
(3) Toggle switches 3pin
(4) ±5V power supply with indicator
(5) Module size: 290mm×150mm×150mm
6. Relay module
(1) +12V relays with indicator and control port
(2) 4mm NC/NO terminals
(3) 2mm NC/NO terminals
(4) Power supply: ±5V, ±12V with indicator
(5) Module size: 290mm×150mm×150mm
7. Command module
(1) Toggle switch/Indicator/8-bit on-off input (8 units each)
(2) Touch switches 12×12×4.3 (24pcs)
(3) PS2 keyboard interface
(4) Independent keyboard interface
(5) 4×4 rectangular keyboard interface
(6) Module size: 290mm×150mm×150mm
8. ADC/DAC module
(1) DAC0832
(2) ADC0809
(3) 0-5V analog voltage source
(4) 8-grade LED level indication
(5) Active clock generator
(6) Module size: 290mm×150mm×150mm
9. AC/DC motor control module
(1) Permanent magnet synchronous motor
(2) DC gear motor
(3) DC5V relays
(4) Signal plates
(5) Photoelectric counter
(6) Module size: 290mm×150mm×150mm
10. Stepping motor control module
(1) Scale
(2) Stepping motor with driver
(3) DC5V relay
(4) Sensors
(5) Motor gear with belt
(6) Module size: 290mm×150mm×150mm
11. Sensor adapter module
(1) 8-bit optocoupler (2 groups)
(2) Four-way sensor interfaces
(3) Connecting terminals
(4) Module size: 290mm×150mm×150mm
12. Extended module
(1) Chip 8255
(2) Chip 74LS245
(3) Extended port wiring leads
(4) 5V power supply with indicator
(5) Module size: 290mm×150mm×150mm
13. Temperature sensor module
(1) Analog temperature sensor LM35
(2) Digital temperature sensor 18B20
(3) DC12V relays
(4) 12V/5V power supply
(5) Resistors
(6) Module size: 290mm×150mm×150mm
14. Nixie Tube Display Module
(1) Dot matrix nixie tube module 8pcs
(2) Common anode nixie tube 8pcs
(3) ON/OFF switch
(4) LED indicators
(5) 5V power supply
(6) Module size: 290mm×150mm×150mm
15. Accessories
(1). Digital multimeter
(2). RS232 communication cable
(3). ISP programming unit
(4). Flat cable suite
(5). Electronic connecting wire suite
(6). Safety connecting wire suite
(7). CD (sample, programming, simulation) (1pcs)
(8). Guide book (1pcs)
7 Motor & Transformer Maintenance & Test Training System Digunakan untuk pembelajaran mengenai motor listrik dan transformator, antara lain : melepas lilitan motor, menggulung ulang, merakit, analisa data, dan keterampilan lain mengenai transformator 1PH, motor induksi 1PH, motor induksi 3PH, dan sebagainya. CHOIEO 66962605 1 168.000.000
Features :
• This trainer is designed with three phase AC adjustable power supply, DC power supply and AC/DC measuring meters. Meanwhile, dedicated disassembling tools are adopted such as motor wire embedding tools, hand operated digital winding machine, etc.
• It is ideal for students to conduct training of single phase transformer, single phase motor and three phase motor, including disassembly, rewind, assembly, short-circuit test, no-load test, breakdown maintenance, etc.
EXPERIMENTS
• Single phase transformer maintenance and test
• Single phase motor maintenance and test
• Three phase asynchronous motor maintenance and test
• DC motor maintenance and test
TECHNICAL PARAMETERS
1. Working power supply: three phase five-wire AC 380V ±5%, 50Hz
2. Safety protection: leakage protection (action current ≤ 30mA), overcurrent protection, fuse protection.
3. Rated power: ≤ 1.1KW 3. Environment temperature: -10°C~+40°C
4. Dimension :1500mm×750mm×1400mm (approx.) 5. Relative humidity: ≤90% (25°C) > BASIC CONFIGURATION
1. Personal safety protection:
(1) The three phase power input is designed with current mode residual-current circuit breaker
(2) The three phase adjustable power output is designed with current protection function, with current transformer for experiment current detection, it can cut off the power when overcurrent appears.
(3) Both DC power and AC/DC instruments are designed with outrange alarm and general power cut off function, which can protect device effectively.
(4) Whole sealing gun type plug-in connecting wires are adopted for experiment connection, the inner core is made of oxygen free copper 128 strand wire and the plug is made of solid copper. The metal part is shielded to avoid electric shock.
2. Power part:
(1) Single phase / Three phase adjustable power supply: Provided with 0~450V three phase adjustable AC power supply (with a three phase autoformer regulator), which can be switched by switch. It has three phase output voltage monitoring function, when the short circuit happens or the current reaches 5A, it can automatically trip and alarm.
(2) DC stabilized power supply: Adjustable range 0~250V, maximum output current 1A, 3 1/2 bit digital display, with short circuit protection and self-recovery function.
3. Measuring instruments:
(1) Digital DC voltmeter 0~300V, three levels (2/ 200/300V), switched by key switch, precision class 0.5, 3 1/2 bit digital display.
(2) Digital DC milliammeter 0~2000mA
(3) Digital AC voltmeter: 0~500V, precision class 0.5
(4) Digital AC ammeter: 0~5A, precision class 0.5
(5) Digital power factor meter: 0~500V, 0~5A, precision class 1.0
Motor and Transformer
1. Transformer (220V without dipping paint)
2. Single phase motor (220V, 180W without dipping paint)
3. Three phase motor (180W without dipping paint)
4. Separately excited DC motor (220V, 180W)
8 Analog Circuit Training Kit Digunakan sebagai perangkat untuk pelatihan tentang rangkaian analog. CHOIEO 66968305A 1 78.028.500
TRAINING CONTENT
Analog Electronics Part
• Usage of commonly used instrument
• Diode characteristic test
• Triode transistor input, output characteristics test
• Transistor single transistor amplifier
• Two-pole amplifier circuit
• Negative feedback amplifier circuit
• Emitter follower
• Field-effect tube amplifier circuit
• Differential amplification circuit
• RC sine wave oscillator
• LC sine wave oscillator
• Operational amplifier parameter testing
• Integrated operational amplifier proportional summation operational circuit
• Integrated operational amplifier integrating and differentiating circuit
• Integrated operational amplifier voltage comparator circuit
• Integrated operational amplifier waveform generator circuit
• Integrated operational amplifier active filter circuit
• Integrated power amplifier
• OTL power amplifier
• Integrated voltage stabilizer
• Series voltage stabilizing circuit
PRODUCT COMPOSITION
1. Dimension: 1500mm×700mm×1600mm (approx.)
2. Working power supply: 220V/50Hz
3. Safety protection: Current mode residual-current circuit breaker, voltage mode leakage protector
4. Training table: Steel and wood structure, iron spraying plastics, wearproof and fireproof panel, equipped with drawer and cabinet for the storage of tools and components. (or aluminum alloy structure optional)
5. Analog circuit experiment part:
(1). Adjustable DC stabilized power supply: 0~30V/1.5A continuously adjustable, automatic shifting, with automatic overload protection and self-recovery function.
(2). Fixed DC stabilized power supply: +5V/3A, ±12V/1A
(3). AC power supply: 18V, 9V, 3V, 0V
(4). Function signal generator: wave form (sine wave, triangular wave, square wave), frequency range: 5Hz~550KHz continuously adjustable, output amplitude: sine wave more than 0-10Vp-p
(5). Frequency meter: measurement range: 1Hz~8MHz, 6-bit digital display, automatic shifting, input impedance ≥1MΩ/20PF, sensitivity
Measuring meter:
(1). Voltmeter: DC200V, class 0.5
(2). Ammeter: DC200mA, class 0.5
(3). Digital multimeter
9 Digital Circuit Training Kit Digunakan sebagai perangkat untuk pelatihan tentang rangkaian digital CHOIEO 66968305A 1 78.028.500
TRAINING CONTENT
Analog Electronics Part
• Usage of commonly used instrument
• Diode characteristic test
• Triode transistor input, output characteristics test
• Transistor single transistor amplifier
• Two-pole amplifier circuit
• Negative feedback amplifier circuit
• Emitter follower
• Field-effect tube amplifier circuit
• Differential amplification circuit
• RC sine wave oscillator
• LC sine wave oscillator
• Operational amplifier parameter testing
• Integrated operational amplifier proportional summation operational circuit
• Integrated operational amplifier integrating and differentiating circuit
• Integrated operational amplifier voltage comparator circuit
• Integrated operational amplifier waveform generator circuit
• Integrated operational amplifier active filter circuit
• Integrated power amplifier
• OTL power amplifier
• Integrated voltage stabilizer
• Series voltage stabilizing circuit
PRODUCT COMPOSITION
1. Dimension: 1500mm×700mm×1600mm (approx.)
2. Working power supply: 220V/50Hz
3. Safety protection: Current mode residual-current circuit breaker, voltage mode leakage protector
4. Training table: Steel and wood structure, iron spraying plastics, wearproof and fireproof panel, equipped with drawer and cabinet for the storage of tools and components. (or aluminum alloy structure optional)
5. Analog circuit experiment part:
(1). Adjustable DC stabilized power supply: 0~30V/1.5A continuously adjustable, automatic shifting, with automatic overload protection and self-recovery function.
(2). Fixed DC stabilized power supply: +5V/3A, ±12V/1A
(3). AC power supply: 18V, 9V, 3V, 0V
(4). Function signal generator: wave form (sine wave, triangular wave, square wave), frequency range: 5Hz~550KHz continuously adjustable, output amplitude: sine wave more than 0-10Vp-p
(5). Frequency meter: measurement range: 1Hz~8MHz, 6-bit digital display, automatic shifting, input impedance ≥1MΩ/20PF, sensitivity
Measuring meter:
(1). Voltmeter: DC200V, class 0.5
(2). Ammeter: DC200mA, class 0.5
(3). Digital multimeter
10 Programmable Logic Controller Training Set Digunakan sebagai perangkat untuk pelatihan penggunaan Programmable Logic Control (PLC). CHOIEO 66965101 1 112.602.000
Features :
• This trainer is suitable for courses such as 'PLC Technology', , 'Electric Appliance and PLC Control Technology' and 'PLC Application'.
• It is mainly composed of control panel, PLC mainframe, modular simulation modules and so on.
• The training table adopts plastic sprayed steel structure and designed with drawer, which is convenient for the storage of tools and modules. The table top is made up of high density board, with fireproof, waterproof and wearproof function.
• Frequency converter and motor can be added to extend the experiment content when needed. (optional)
• Safety protections: grounded, lead protection, safety in accordance with related GB standards. Insulated safety sockets, sheathed cables and wires.
TRAINING CONTENT
• PLC basic instruction training
• Motor forward and reverse control simulation
• Television transmitting tower simulation
• Traffic light control system simulation
• Automatic goods delivery and loading system simulation
• Automatic water tower water level control simulation
• Automatic molding machine system simulation
• Various liquids automatic control system simulation
• Automatic punching machine control system simulation
• Elevator control system simulation
• Automatic mail sorting system simulation
• Automatic washing machine control system simulation
• Plating control system simulation
• Automatic vending machine system simulation
• Relay control experiment
• Software simulation control
TECHNICAL PARAMETER
1. Input Voltage : AC 380V/220v, 50Hz 2. Temperature : -5~40°C, Below RH 90% 3. Overall power consumption: 0.3 kVA 4. Dimensions: table 1575mm×680mm×835mm (approx.) bench 1130mm×250mm×720mm (approx.) >BASIC CONFIGURATION 1. Training table: it adopts steel-wood material, with 16mm medium density fiberboard as the tabletop. The frame is made of rectangular steel tubes. The structure is designed with two drawers, PC cabinet, keyboard tray and lockable universal wheels.
2. Round stool (2pcs): Screw lifting range: 450~500mm, seat size: 300mm×300mm (approx.)
3. Control panel:
(1) AC power control unit: It is equipped with lighted fuse and leakage protection switch and provided with three phase 380V and single phase 220V power supply (one group each), which can be controlled by start-stop switches. Three-phase-four-wire AC 380V supply via air switch and can be monitored by voltmeter.
(2) Timer and alarm recorder: It has time setting, timing alarm, power cut-off function and can automatically record the electric leakage alarm time, which is caused by connection or operation.
(3) DC stabilized voltage: 0~30V adjustable, with rough/accurate adjust rotary knobs.
(4) DC constant current source: 0~200mA adjustable, with rough/accurate adjust rotary knobs.
(5) DC digital voltmeter: 0~200V, 10MΩ, class 0.5
(6) DC digital ammeter: 0~200mA, class 0.5
(7) Logic level output and indicator, self-locking/jog buttons
(8) Programmable logic controller: FX1N-40MR, 24I/16O, relay output
4. PLC simulation module (standard modular dimension 150mm×288mm×50mm)
(1) Motor positive and negative rotation control
(2) Television transmitting tower
(3) Traffic light control system
(4) Automatic goods delivery and loading system
(5) Automatic water tower water level control
(6) Automatic molding machine system
(7) Various liquids automatic control system
(8) Automatic punching machine control system
(9) Elevator control system
(10) Automatic mail sorting system
(11) Automatic washing machine control system
(12) Plating control system
(13) Automatic vending machine system
(14) Relay control experiment
5. Experiment wire: Length: 40cm/60cm/100cm, red/yellow/black, 60pcs in total.
6. PLC Programming software(copy): GX-Developer, It can accomplish the edit of PLC ladder diagram, instruction list, SFC,etc. The program can be saved as GPPQ, GPPA format.
7. Programmable cable: USB2.0 PC port, round head 8-pin PLC port, with 3 color LED communication indicator and driver disc (one-button type installation, available for windows XP, VISTA, WIN7, etc.).
8. Simulation software (copy): GX simulator.
9. PLC program: Programs for 14 simulation modules, 27 basic instructions, advanced instruction application
10. Power socket
Instruction module, Power adapter module, Test line, CD, Download line, User Manual.
11 Basic Electro Pneumatic Training System Digunakan sebagai perangkat untuk pelatihan elektro pneumatik dasar. CHOIEO 66971105 1 195.000.000
Features :
• The electro pneumatic training platform is made up of experimental table, frame, pneumatic components, electrical control modules and so on.
• Modular structure design is adopted for experiment construction, each pneumatic component is an independent unit that comes with mounting baseboard. Reliable quick connectors are used for the connection of components.
• Aluminum alloy profile panel, with ‘T’ type mounting slot for pneumatic components installation and circuit construction. All solenoid valves, sensors and mircoswitches are designed with 4mm safety plug sockets for quick connection.
• The air compressor adopts air oil-less type compressor, which has the advantage of light weight, low power consumption and low noise.
• Safety protections: grounded, lead protection, safety in accordance with related GB standards. Insulated safety sockets, sheathed cables and wires.
TRAINING CONTENT
• Understanding of pneumatic structure and components
• Single acting cylinder manual reversing controlled loop
• 5/3 way solenoid directional valve controlled single acting cylinder loop
• 5/2 way single solenoid directional valve controlled single acting cylinder loop
• 5/2 way double solenoid directional valve controlled single acting cylinder loop
• Double acting cylinder hand directional valve control loop
• Double acting cylinder 5/2 way single solenoid directional valve control loop
• Double acting cylinder 5/2 way double solenoid directional valve control loop
• Single acting cylinder inching control loop
• Double acting cylinder inching control loop
• Sensor (capacitive/ photoelectric/ inductive) application control loop
• Dual pressure valve control loop
• Quick exhaust valve application control loop
• Sequence valve application control loop
• Time delay valve application control loop
• Four-cylinder linked action loop
• Double acting cylinder one-way speed regulation loop
• Double acting cylinder both-way speed regulation loop
TECHNICAL PARAMETERS
1. AC power input: single phase AC220V±10%, 50Hz, 10A
2. Environment temperature: -10ºC~40 ºC Ambient humidity ≤ 85% (25 ºC)
3. Overall consumption: ≤ 2KVA
4. Working power supply: DC24V, 4.5A with short circuit protection function
5. Dimension: 1300mm×600mm×1700mm
6. Aluminum plate:1200mm×735mm (approx.)
PNEUMATIC COMPONENTS
1. Single acting cylinder (spring return) (Qty:1)
2. Double acting cylinder (Qty:3)
3. Air service unit (reduce valve/lubricator/filter) (Qty:1)
4. Reduce valve with pressure gage (Qty:1)
5. (5/2way) single solenoid valve (Qty:2)
6. (5/2way) double solenoid valve (Qty:1)
7. (5/2way) hand directional valve (Qty:1)
8. (3/2way) solenoid valve (Qty:1)
9. Air on/off valve (Qty:1)
10. (5/2way) double pneumatic valve (Qty:2)
11. (5/2way) single pneumatic valve (Qty:2)
12. Sequence valve (Qty:1)
13. Rotary cylinder (Qty:1)
14. Shuttle valve (Qty:2)
15. Dual pressure valve (Qty:1)
16. Time delay valve (Qty:1)
17. Quick exhaust valve (Qty:1)
18. One way valve (Qty:2)
19. Button valve (Qty:1)
20. Rotary valve (Qty:1)
21. Stroke valve (Qty:1)
22. Mushroom head button valve (Qty:1)
23. Throttle valve (Qty:6)
24. Capacitive sensor (Qty:4)
25. Photoelectric sensor (Qty:4)
26. Inductive sensor (Qty:4)
27. Magnetic reed switch suite (for cylinder) (Qty:1)
28. Microswitch (left trigger) (Qty:2)
29. Microswitch (right trigger) (Qty:2)
ELECTRICAL CONTROL
1. Control panel board
(1) High brightness aluminum-plastic panel
(2) Size: 1200mm×735mm
2. Power part
(1) Six way DC 24V
(2) Three way single phase AC220V
(3) Leakage protective switch, emergency stop button, key on/off switch, main power indicator
3. Inching buttons
(1) 1NC/1NO inching button: 1 red, 2 green
(2) 1NO inching button: green
4. Self-locking rotary knobs: 1NC/1NO, two groups
5. Indicating light: 1 red, 1 green with connecting sockets
6. Relay part
(1) 3NO/3NC relay: 5-fold, with led indicators
(2) 1 timer relay, adjustable with delayed pick-up
(3) 1 timer relay, adjustable with delayed release
ACCESSORIES
1. T-joint (Qty:10)
2. Cross joint (Qty:10)
3. Y-joint (Qty:10)
4. Air tube suite (Qty:1)
5. Tube plug (Qty:20)
6. Mounting base (Qty:5)
7. Air compressor:
(1) Motor power: 550W
(2) Rated current: 2.8A
(3) Input voltage: 220V, 50Hz
(4) Speed: 1380r/min
(5) Flow: 40L/min
(6) Capacity: 30L 8. Tools: straight screwdriver, scissors, nipper pliers, cross screwdriver, monkey wrench, sealing tape, socket head wrench
12 Basic Electro Hydraulic Training System SSEDU ZMH-1107 1 540.000.000
13 Mesin Bubut Konvensional Untuk pengenalan dan pelatihan pengerjaan benda kerja menggunakan mesin bubut konvensional RICHON CZ-1440G/1 1 207.759.000
Features :
Supersonic frequency hardened bed ways
Precision roller bearing for spindle
High quality steel, ground and hardened gear inside headstock
Easy and fast operating gearbox
Enough strong power motor
ASA D4 camlock spindle nose
Various threads cutting functions available
Technical Data
Swing over bed mm φ355,Swing over carriage mm φ220
Swing over gap mm φ500,Width of bed-way mm 186
Distance between centers mm 1000,Taper of spindle M.T.5
Spindle diameter mm φ38,Step of speed 8
Range of speed rpm 70~2000,Head D1-4
Metric thread 26kinds (0.4~7mm),Inch thread 34kinds(4~56T.P.I)
Moulder thread 16 kinds(0.35~5M.P),Diametral thread 36 kinds(6~104D.P)
Longitudinal feeds mm/r 0.052~1.392 (0.002”~0.0548”)
Cross feeds mm/r 0.014~0.38 (0.00055”~0.015”)
Diameter of lead screw mm φ22(7/8”)
Pitch of lead screw 3mm or 8T.P.I
Saddle travel mm 1000,Cross travel mm 170,Compound travel mm 74
Barrel travel mm 95,Barrel diameter mm φ32,Taper of center mm M.T.3
Motor power Kw 1.5(2HP),Motor for coolant system’s power Kw 0.04(0.055HP)
approx. Machine(L×W×H) mm 1920×750×760,Stand(left) (L×W×H) mm 440×410×700
approx. Stand(right) (L×W×H) mm 370×410×700
approx. Machine Kg 505/565,Stand Kg 70/75
Standard accessories:
Three jaw chuck,Four jaw chuck,Steady rest,Follow rest,Lathe stand
Center,Center sleeve,Change gear,Oil gun,Working light,Coolant system
Foot brake,Tools and tool box
14 Pipe Thread Machine Untuk mengenalkan dan memberi keterampilan membuat ulir pada pipa menggunakan pipe thread machine BOL ZIT-R2 1 19.032.000
Specifications:
Pipe capacity: 1/2"-2"
Bolt capacity: M12-M33
Conduit capacity: C15,C19-31,C39-51(optional, Die for conduit is not standard accessories)
Applicable threader standards: BSPT,NPT, BSPP,BSW,Metric (need to exchange additional Die)
Power: 750W
Speed: 28 RPM
Voltage: 220V~ or 110~ single phase
Frequency: 50Hz or 60Hz
Switches FOR/OFF and safety foot switch optional
Die: Alloy or HSS
Cutter: Wheel type, self-centering
Reamer: 1/2"-2" cone blade, 5-flute cone optional
Oil pump: Gerotor Oil Pump
Gross/net weight: 85/73Kg
Packing size: 720x480x560mm
Standard Accessories
Two manual type Die Head
One set of 1/2”-3/4” Die
One set of 1”-2” Die
One set of M12 Die
One set of M14-M16 Die
One set of M18-M22 Die
One set of M24-M27 Die
One set of M30-M33 Die
One set of 1/2"-2"Cutter Kit
One set of 1/2"-2"Reamer Kit
Three pcs of Tubular Supporter
15 Gerinda Listrik Tangan Untuk mengenalkan dan memberi keterampilan menggerinda atau menghaluskan permukaan benda kerja menggunakan mesin gerinda tangan HIKOKI G 10SS 1 1.800.000
Specifications
Capacity: Wheel Dia 100mm (4")
Capacity: Hole Dia 16mm (5/8")
Spindle Thread M10 x 1.5
Power Input 600W ~ 650W
No Load Speed 11,500/min. : 220-240V
12,000/min. : 110-120V
Overall Length 254mm (10")
Weight*3 1.7kg (3.8lbs.)
Standard Accessories Side Handle, Wrench
16 Mesin Gerinda Potong Untuk mengenalkan dan memberi keterampilan memotong bahan baku produk menggunakan mesin gerinda potong. HIKOKI CC14SST/STD 1 6.097.500
Features :
Power input 2,200W
Quick lock vise
Spark diversion guard
Spindle lock
Specifications
Capacity:Cut-off Wheel Dia. 355mm (14")
Power Input 2,200W
No Load Speed 3,800/min.
Max Workng Perphera Speed 4,800m/min.
Dimensions (L x W x H) 590 x 300 x 640mm (23-7/32" x 11-13/16" x 25-3/16")
Weight 17.0kg (37.4 lbs.)
Standard Accessories Cut-off Wheel, Wrench
Round pipe approx. 115mm/Square approx. 115x115mm/Rectangle approx. 150x102mm
17 Digital optical measurement profile projector Untuk alat ukur komponen yang relatif kecil. SINPO JT-300 1 296.250.000
Features:
-The up and down system adopts linear guide way and nuts without interference. It's more comfortable and stable.
-The reflecting mirror adopts patent coating techniques with good anti-dust effects.
-The transmission illumination has high and low levels, which can meet different measuring requirements.
-Light source adopts Philip tungsten halogen lamp with high brightness and long using life to satisfy long time using demands.
-Axial flow fan with strong dissipations heat function dissipates heat in double directions
-The optical system has excellent quality, the objective forms clear image and the magnification is accurate.
-The working distance on object is large, which can meet measuring requirements of different parts.
-The RS232 port can realize the output and communication of data with computer.
- It is erect image with external DRO which is according to the operator's habits.
Technical parameters:
-Screen Diameter: Φ300mm
-Rotating range: 0°~360°
-Resolution of the rotary angle: 1
-Accuracy of the rotary angle: 6
-Objective
Magnification Object Visual Field (mm) Object Working Distance (mm)
10X φ30 75.201
20X φ15 69.599
50X φ6 44.4
100X φ3 26.243
DS600 or DS401 Box
-Errorof magnifying power ≤ 0.08%
-Worktable area: 400×225mm
-Travel of workstage: X=200mm Y=100mm Z=90mm
-Display equivalent of X Y: 1μm
-Accuracy of instrument: (3+L/75) um, L unit: Mm
-Load capability of worktable: 5kg
-Lighting source
Transmission lighting: 12V 100W Halogen tungsten lamp
Reflecting lighting: 24V 150W Halogen tungsten lamp
-Overall sizes of the instrument (mm): 694×380×1065
-Machine Weight: 135 kg
-Ambient environment of the instrument service
-Working temperature: 20±5'C
-Relative humidity: Not more than 60%
18 Power Block Merupakan mesin bantu yang digunakan untuk menarik jaring pukat cincin dari dalam air ke atas deck kapal, bisa bertenaga hidrolik maupun listrik. KERNEL HHXG-KA2 1 30.000.000
Technical Data
Rated load(kg) 2000
Load Chain(mm×mm) φ8×24
Handle Control Voltage(V.AC) 24
Power(KW) 1.1
Lifting height(m) 3
Lifting speed(m/min) 2.5
Work Rate S3-30% 20 min
Rated Volt(V) 220 V 50 Hz
Packing Size(mm) 690×410×470
N.w(kg) 54
19 Manual Shearing Machine Untuk mengenalkan dan memberi keterampilan memotong lembaran plat menggunakan manual shearing machine. RICHON Q01-1.5X1320 1 77.962.500
Product Description
The shearing machine with both front and back gauge
Used for mild steel aluminum copper, brass zinc plastic and leads
Features:
The Manual shear is with both front and back gauge
With heavier weight, good stability
High carbon and chrome steel blade
A fully casting structure, not easy deformation
Used for mild steel aluminum copper, brass zinc plastic and leads
It features convenient operation and high efficiency.
Technical Data
Width (mm) 1320
Length (mm) 1500
Max. Shearing thickness (mm) 1:05
Back gauge range (mm) 0-700
Packing size (cm) 168x76x115
N.W./G.W. (kg) 491/545
20 Band Saw Machine Untuk mengenalkan dan memberi keterampilan memotong bahan baku produksi menggunakan band saw machine. RICHON BS-912B 1 85.800.000
Main features:
Adjustable hydraulic feed cutting rate for multiple applications
Mitre cuts to 45º using calibrated vice
Built-in coolant system to both blade guides for maximum cutting efficiency
Limit switch stops machine when cut is complete
Quick action material clamping lever
Adjustable blade roller guides provides accurate cutting
Adjustable 4-speed pulley drive system enabling 26-50-73-95mpm cutting speeds
Adjustable length stop for repetition cutting
Wire wheel brush to clean swarf from blade
Portable - on wheels for ease of use
Automatic electric cut-out switch
Technical Data
Capacity
Circular @90° mm/'' 229(9)
Rectangular @90° mm/'' 178×305(7×12)
Circular @45° mm/'' 150(6)
Rectangular @45° mm/'' 127×150(5×6)
Blade speed @50HZ MPM
@60HZ MPM 26,50,73,95
Blade size mm 27×0.9×2655
Motor power W/HP 1100/1500 ~ 2.0/1.0
Drive . V-belt
Packing size cm 154×59×115
N.W./G.W. kg 230/260
21 MMA Welding Machine Untuk mengenalkan dan memberi keterampilan mengelas menggunakan las MMA. TOPWELL STICK-200HD 1 13.275.000
Technical specifications
Rated Input Voltage 1PH ~ 230V ±15%
Max. Load Power Capacity 8.75 KVA ~ 14KVA
Rated Duty Cycle(40℃) 60% 200A/28V
100% 180A/27.2V
Welding Current/Voltage Range 20A/20.8V~200A/28V
Open Circuit Voltage 70V~80V
Power Factor 0:08
Efficiency 80%
MMA Arc Force Preset
Hot Start Time Preset
Hot Start Current Preset
Dimension 345X145X230mm
Weight 4.6KG
22 MIG-MMA Welding Machine Untuk mengenalkan dan memberi keterampilan mengelas menggunakan las MIG. TOPWELL MIG-200Di 1 19.492.500
Technical specifications
Rated Input Voltage 1PH ~ 230V ±15%
Max. Load Power Capacity 8.75KVA
Rated Duty Cycle(40℃) 35% MIG: 200A/24V
MMA: 200A/28V
TIG: 200A/18V
100% MIG: 160A/22V
MMA: 160A/26.4V
TIG: 160A/16.4V
Welding Current/Voltage Range MIG: 10A/14.5V ~200A/24V
MMA: 20A/20.8V~200A/28V
TIG: 5A/10.2V~200A/18V
Open Circuit Voltage 70V~80V
Power Factor 0:08
Efficiency 80%
Pre-Gas Time Preset
Flow-Gas Time Preset
Wire-feed Mechanism 2 Rollers
Wire-feed Speed Range 2-18m/min
Wire Spool Capacity 200mm (5kg)
Filler Wires Ø (mm) Fe, Ss 0.6~1.0 mm
Dimension: 490x230x385mm
Weight 20KG
23 TIG Welding Machine Untuk mengenalkan dan memberi keterampilan mengelas menggunakan las TIG. TOPWELL Alutig-200P 1 35.100.000
Technical specifications
Rated Input Voltage 1PH ~ 115/230V ±15%
Max. Load Power Capacity TIG:5.63KVA
MMA:6.60KVA
Rated Duty Cycle(40℃) 60% TIG: 200A/18V
MMA: 160A/26.4V
100% TIG: 160A/16.4V
MMA: 130A/25.2V
Welding Current/Voltage Range TIG: 5A/10.2V~200A/18V
MMA: 20A/20.8V~160A/26.4V
Open Circuit Voltage 70V~80V
Power Factor 0,06875
Efficiency 80%
TIG Pulse Peak Current
Pulse Frequency 0.2Hz~200Hz
Pulse Width (Ratio) 1~100%
AC TIG AC Frequency Range 20Hz~250Hz
AC Clean Width (AC Balance) +40~-40
AC Clean Ratio (AC Bias) % +30~-50
MIX TIG MIX Frequency: 1Hz~5Hz
DC Balance: (%) 20~80
Arc-starting Current 5A~250A
Crater-filling Current 5A~250A
Current Up-slope Time 0.1S~15S
Current Down-slop Time 0.1S~15S
Pre-Gas Time 0.1S~15S
Flow-Gas Time 0.1S~15S
Spot Arc Time 0.1S-10S
MMA Arc Force 10A~160A
Hot Start Time 0.1~3S
Hot Start Current 10A~160A
Dimension (LxWxH) 540x240x480mm
Weight (KG) 23KG
24 Plasma Cutting Welding Machine Untuk mengenalkan dan memberi keterampilan mengelas menggunakan las plasma. TOPWELL CUT-60Di 1 50.775.000
Technical specifications
Item No CUT-60Di
Input voltages (±15%) 200–240V, 1-PH, 50-60Hz
Max Input current 200/240V, 48/40A
Output current 30-60A
Rated output voltage 104V
Duty cycle @ 40° C (104° F) 60% @60A
100% @40A
Open circuit voltage (OCV) 280V
Dimensions 540x240x480mm
Weight 19kg
Gas supply Air (clean, dry and oil-free)
Recommended gas inlet flow rate/pressure 0.3-0.5Mpa
Power supply type Inverter – IGBT
Electrical efficiency 80%
Max. Load Power Capacity 9.7KVA
Certifications CE, RoHS
Warranty Power supply: 3-year
Torch: 1-year
25 Hand Tool Set Technical Data : KERNEL W2163 1 12.150.000
1 piece Tricolor handle very long “one” word screwdriver 6 * 250mm
1 piece Tricolor handle very long Cross Screwdriver PH2 * 250mm
1 piece Tricolor handle very long Cross Screwdriver PH1 * 250mm
1 piece color handle clock ”one” word screwdriver 1.4 * 60mm
A piece of two-color handle clock ”one” word screwdriver 1.8 * 60mm
A piece of two-color handle clock ”one” word screwdriver 2.5 * 60mm
A piece of double color handle clock ”one” word screwdriver 3.0 * 60mm
1 piece color handle clock cross screwdriver PH00 * 60mm
1 piece double color handle clock cross screwdriver PH0 * 60mm
1 piece 6.3mm series rotary handle
1 piece 6.3mm series screwdriver change head
20 pieces batch head
1 piece double-colored needle mouth pliers 6 inch
1 piece double-colored diagonal bevel pliers 6 inch
1 piece of olecranon wire stripper
1 piece network crimping pliers 6P8P
9 pieces metric strong sleeve
1 piece automatic range digital multimeter
1 piece electric iron 30W (CCC certification)
1 piece of solder wire 10g
1 piece gold aluminum suction tin
1 piece pointed tweezers
1 piece curved blade electrician
9 pieces metric folding internal hexagon
1 piece hand saw 10 inches
1 piece digital display pen
1 piece of insulation tape 9M
1 piece working headlight
26 Electric Drill Technical Data HIKOKI DV10VST 1 2.250.000
Chuck Capacity 10mm (3/8")
Capacity: Steel 10mm (3/8")
Capacity: Wood 25mm (1")
Power Input 450W
No Load Speed 0 - 3,200/min.
Overall Length (with Keyed Chuck) 227mm (8-15/16")
Overall Height (with Keyless Chuck) 176mm(6-15/16")
Weight (with Keyed Chuck) 1.2kg (2.6lbs.)
Standard Accessories Chuck Wrench
Torque set: 23+1
Max torque force: approx. 35N.m
27 Impact Drill Kit Features : FIXTEC FID600K50 1 2.250.000
600w Impact Drill kit with 50pcs accessories
Tackle tough jobs with the impact drill kit with 50pcs accessories from Power Tools.
A switch lets you set the tool to operate as a traditional drill or a hammer drill with a hammering action.
A detachable side-assist handle offers greater control, as does the two-finger, variable-speed precision trigger.
Technical Data
Model Number
Voltage/Frequency 230v/50Hz
Input power 600W
Chuck size 13mm
No-load speed 0-3000rpm
Reversible Yes
Max impact rate 48000bpm
Drilling capacity:
steel: approx. 13mm/ concrete: approx. 13mm/ wood: approx. 25mm With 50pcs accessories
28 Rotary Hammer Technical Data FIXTEC FRH85001 1 3.300.000
Voltage 220-240V ~ 50-60Hz
Rated power 850W
No load speed 900rpm
Impact rate 4000bpm
Impact energy per stroke 5.0J
Tool holder SDS-PLUS
Max. drilling dia.
- Steel 13mm
- Wood 42mm
- concrete 26mm
Weight 4.6KG
Protection class II
Impact Joules: 5J Drilling capacity:
steel: approx. 13mm/ concrete: approx. 26mm/ wood: approx. 42mm Accessories:
29 Multi-function Tools Specifications and Features OSTAR MT400-01 1 2.340.000
Volt: 230~240V/50Hz
No-load Oscillation Speed: 11000~20000RPM/min
Oscillation Angle: 4.5 Degree
Power: 400W(VDE)
Machine Weight: 1.3 kg
Packing: BMC+Brown Box
Regular Accessories:
1X scraper/Straight Cut Blade /sanding pad,3pcs sanding paper
Main Feature:
* Quite Light +Best Blance+Variable Speed Control
* Slim Body + Comfortable Soft Grip
30 Drill Press Specifications : KERNEL ZHX-13 1 17.700.000
Maximum Drilling Capacity 13 mm
Diameter of Column 46 mm
Spindle Travel 50 mm
Distance Spindle Axis to Column Generating Line 103 mm
Max. Distance Spindle Nose to Table 220 mm
Max. Distance Spindle Nose to Base 300 mm
Spindle Taper B16
Spindle Speed Range 515-2580 rpm
Spindle Speed Series 5
Dimension of Worktable Surface 160x160 mm
Dimension of Base 280x180 mm
Overall Height 580 mm
Power of Motor 180W
Voltage 220V
Gross / Net Weight 21/19 kg
Packing Dimension 460Hx330Lx230W mm
Kompetensi Keahlian Teknika Kapal Niaga
No Nama Alat Merk Tipe Qty Harga Satuan
1 Engine Room Simulator TRANSAS 1 30.000.000.000
2 Motor Diesel DEUTZ MB-DY200 1 1.177.789.500
3 Motor Bensin PARSUN F40BWS-T-EFI 1 235.500.000
4 Insatalasi Poros Baling-baling -
5 Basic Electronics Trainer SSEDU ZE1110 1 31.719.000
6 MCU Training Set CHOIEO 66968201 1 138.000.000
7 Motor & Transformer Maintenance & Test Training System CHOIEO 66962605 1 168.000.000
8 Analog Circuit Training Kit CHOIEO 66968305A 1 78.028.500
9 Digital Circuit Training Kit CHOIEO 66968305B 1 78.028.500
10 Programmable Logic Controller Training Set CHOIEO 66965101 1 112.602.000
11 Basic Electro Pneumatic Training System CHOIEO 66971105 1 195.000.000
12 Basic Electro Hydraulic Training System SSEDU ZMH-1107 1 540.000.000
13 Mesin Bubut Konvensional RICHON CZ-1440G/1 1 207.759.000
14 Pipe Thread Machine BOL ZIT-R2 1 19.032.000
15 Gerinda Listrik Tangan HIKOKI G 10SS 1 1.800.000
16 Mesin Gerinda Potong HIKOKI CC14SST/STD 1 6.097.500
17 Digital optical measurement profile projector SINPO JT-300 1 296.250.000
18 Power Block KERNEL HHXG-KA2 1 30.000.000
19 Manual Shearing Machine RICHON Q01-1.5X1320 1 77.962.500
20 Band Saw Machine RICHON BS-912B 1 85.800.000
21 MMA Welding Machine TOPWELL STICK-200HD 1 13.275.000
22 MIG-MMA Welding Machine TOPWELL MIG-200Di 1 19.492.500
23 TIG Welding Machine TOPWELL Alutig-200P 1 35.100.000
24 Plasma Cutting Welding Machine TOPWELL CUT-60Di 1 50.775.000
25 Hand Tool Set KERNEL W2163 1 12.150.000
26 Electric Drill HIKOKI DV10VST 1 2.250.000
27 Impact Drill Kit FIXTEC FID600K50 1 2.250.000
28 Rotary Hammer FIXTEC FRH85001 1 3.300.000
29 Multi-function Tools OSTAR MT400-01 1 2.340.000
30 Drill Press KERNEL ZHX-13 1 17.700.000
Kompetensi Keahlian Teknika Kapal Niaga
No Nama Alat Deskripsi Merk Tipe Qty Harga Satuan
1 Engine Room Simulator Digunakan untuk pengenalan mengenai ruang mesin pada kapal, sistem pendingin, sistem mesin bantu,dan kelistrikan. TRANSAS 1 30.000.000.000
- Configured with realistic consoles and several large monitor so to reproduce the ER different
areas.
- Engine
• Low Speed diesel, with CPP or FPP, with conventional or electronic control
• Medium Speed diesel,
• Medium Speed diesel, up to 4 engines, gear and CPP
• Steam turbine, with FPP
• Gas turbine, with CPP
• All related auxiliary equipment (electricity generation, Sea water cooling, Lubricating oil etc as below specified)
- AuxiliAry system
• Air Conditioning and refrigeration Plant
• Power Plant
• Treatment Plant (separators, reverse osmosis system, etc.)
• Freshwater plant
• Marine equipment (Compressors, pumps,
2 Motor Diesel Digunakan untuk mengenal jenis-jenis penggerak motor pada mesin kapal DEUTZ MB-DY200 1 1.177.789.500
DEUTZ Generator Set
Generator Model MB-DY200
Prime Power 200KW/250KV
Power Factor COSΦ=0.8
Genset Weight 2300KG
Dimensions(L×W×H) 1800mm×650mm×1450mm
Rated Voltage 400/230V
Rated Frequency 50Hz
Diesel Engine
Brand Deutz
Engine Model TD226B-4D
Rotating Speed 1500RPM
Power 66KW/82.5KVA
Fuel Consumption at 100% Load ≤209g/kw.h
Total Lubrication System Capacity 38L
Bore×Stroke 105×120 mm
Compression Ratio 15.5 : 1
Displacement 4.16L
Engine Structure 4 Cylinder,4 Stroke
Cooling System Forced Water Cooling Cycle
Governing system Mechanical Governor/ Electronic Governor(Option)
Starting Method 24V Electrical starting
Engine Filtration System Dry Air Filter,Fuel Filter,Engine oil Filter
3 Motor Bensin Digunakan untuk mengenal jenis-jenis penggerak motor pada mesin kapal PARSUN F40BWS-T-EFI 1 235.500.000
40HP EFI outboard specification:
Engine type 4-stroke,3-cylinders, OHC
Displacement 747 cc
Bore x Stroke mm(in.) 65.0×75.0(2.56×2.95)
Max output Kw(HP)@ r/min 29.4(40)@5000
Fuel induction system Electric Fuel Injection
Ignition system Micro Computer
Starting system Manual / Manual + Electric
Steering system Tiller handle
Gear shift Forward-Neutral-Reverse
Gear ratio 2.0(26/13)
Trim and tilt system Power trim&tilt
Max fuel consumption 13.8 L/h
Fuel tank capacity 24L
Sump oil capacity 1:07
Gear oil capacity 430cc
Dry weight 92.4kg~101.5kg
Alternator output 12V 200W
Recommended transom height 381mm (15 in.)
4 Insatalasi Poros Baling-baling Digunakan untuk pengenalan cara kerja sistem baling-baling pada kapal -
Length: 900–2000 mm
Input power: 200 – 2000 hp Input speed: 2500 – 3600 rpm Steering angle: 35 – 40 degree trim angle: 15 degree
weight: 70 – 700
body material: SS
5 Basic Electronics Trainer Digunakan sebagai perangkat untuk menjelaskan elektronik dasar. SSEDU ZE1110 1 31.719.000
I. Technical parameter:
1. Power
Input: AC220V±10%
Output:(1)DCV ,±12V/0.2A,DCI≥0.2A(2)DCV,±5V/2A,DCI≥1A
2. Signal source
(1)function generator
output wave shape: Square wave triangle wave sine wave
Amplitude: square wave triangle wave sine wave : (0 ~ 10 V for peak-peak)
Frequency range: it can be divided to 4 range: 0HZ~200HZ, 200HZ~10KHZ, 10KHZ~100KHZ, 100KHZ~200KHZ
(2)DC signal, double way, ±5V, ±0.5V, it can be adjust continuously
3. supply 4 single pulse generator
4. Four ways (T1, T2, T3, T4) sequence generator, and start and stop circuit
5. 1HZ~10MHZ pulse output
6. 12 ways switch output display circuit
7. 6 bits 7 segment LED displayer
8. 2 ways BCD code switch
9. The system has many 8P~40P common round hole, IC experiment circuit plug and socket, with resistor for 1K, 10K, 22K, 100K, 680K etc. and contact safety socket, it can connect resistor, capacitor, it can do pulse experiment, digital circuit experiment, logic circuit and many basic experiment.
10. 555 timer base circuit with audio output control
11. Six high precision digital frequency meter, test range: 0-9.9999MHZ error range: <1HZ(it is designed by CPLD chip)
12. Supply with 3 and a half digital voltage meter
13. It has potentiometer group and resistance capacitance and inductance diode electronic component, and easy for students to use.
14. Analogue circuit experiment zone is made of single pipe two pipe differential amplifiers and integrated op-amp rectifier voltage filter of circuits, etc
15. Experiment area use metal needle, use a medium sized hole, never oxidation, beautiful and beautiful, practical strong, experiment with wires plug metal paint process, inserted more convenient, more reliable contact, and long service life
II. Experiment content
Digital part experiment contain:
1.TTL logical gate parameters test and use
2.CMOS Integration logic gate of the test
3.Gate circuit logic function test
4.Common combination logic function components test
5.Data collect and application
6.Blood type relationship detection circuit and voting circuit
7.RS function of the trigger and test
8.JK trigger logic function and main parameters test
9.The shift register function test
10.Decade computer(CMOS)
11.Asynchronous counter
12.Synchronous counter
13.Count decode display circuit experiment
14.555 Integrated timer and application
15.Sequential detector
16.Follow type is A/D conversion circuit
17.Artificial control traffic light controller
18.Automobile tail light control circuit
19.Digital circuit design
20.Timing circuit testing and research
21. Wave shape generate and monostable trigger
22. A/D convert circuit
23. D/A convert circuit
Analog part experimental contents:
1, Rectifier voltage filter and parallel circuit
2, Series voltage stabilizing circuit
3, Integrated voltage stabilizing circuit
4, Integrated power amplifier
5, Complementary symmetry power amplifier
With bread board and expand chip
6 MCU Training Set Digunakan sebagai perangkat untuk pelatihan/percobaan tentang micro computer dasar. CHOIEO 66968201 1 138.000.000
Features
• This trainer adopts modular and open type design, each module can be used separately for basic experiment or combined for training experiment and course design.
• The training table is designed with drawer cabinet for module storage and four lockable universal caster wheels for easy movement. When doing experiment, the top surface of table can be folded so that students can put modules on base plate to conduct training. The table can also be used as a normal desk when the top surface is closed.
• The modules use high strength PCB as the carrier, the front side is printed with terminal signals and equipped with main components, the wiring is conducted on the back side.
• It covers various microcontroller training courses, such as I/O training, A/D training, D/A training, LED/LCD dot matrix module experiment, motor control, etc. Besides, mechatronics application can be extended on this trainer by adding an intelligent material handling device.
TRAINING CONTENT
• Lights flash training
• Marquee’s training
• Independent key input training
• Photoelectric isolation input and output training
• Metal detection training
• Dynamic nixie tube display training
• Matrix keyboard interface training
• Relay isolation control training
• Buzzer playing training
• The expansion of IO port with 8255 chip training
• 1602 liquid crystal display module control training
• 128*64 LCD module control training
• Dot matrix LED screen character display training
• AD conversion training
• DA conversion training
• LM35 temperature sensor acquisition training
• Single bus temperature sensor acquisition training
• The control of AC/DC gear motor training
• Open loop control of step motor training
• RS232 communication training
TECHNICAL PARAMETERS
1. Power input: AC220V±10% (safety plug output, with leakage protection function)
2. Output voltage: (DC±12V±5%, 1A); (DC±5V±5%, 1A); (DC24V±5%, 1.5A)
3. Working environment: temperature -10ºC~+40ºC, relative humidity
BASIC CONFIGURATION
1. Training table /Worktable
(1) Powder coating steel frame
(2) Foldable table face
(3) Storage cabinets
(4) Universal lockable wheels
2. Power module
(1) Switch: leakage protector, rocker switch
(2) Power supply: ±12V, +24V, ±5V, AC220V
(3) Switching power supply 2 units
(4) Power indicator and safety sockets
(5) Module size: 290mm×285mm×100mm
3. Mainframe module
(1) Integrated chip: ATMEGA48-10PU, AT89S52
(2) Pin header: 1×40 with locking mechanism
(3) Dial switch 4T, active buzzer
(4) A type USB jack and D type DB232-9T curved needle
(5) Interface: RS232, on-system download interface
(6) Module size: 290mm×150mm×150mm
4. Emulator module
(1) 51 microcontroller emulator
(2) Power supply interface
(3) USB interface
(4) Emulator interface
(5) Module size: 290mm×150mm×150mm
5. LCD module
(1) 128×64 Graphic Type LCD
(2) 1602 character type LCD
(3) Toggle switches 3pin
(4) ±5V power supply with indicator
(5) Module size: 290mm×150mm×150mm
6. Relay module
(1) +12V relays with indicator and control port
(2) 4mm NC/NO terminals
(3) 2mm NC/NO terminals
(4) Power supply: ±5V, ±12V with indicator
(5) Module size: 290mm×150mm×150mm
7. Command module
(1) Toggle switch/Indicator/8-bit on-off input (8 units each)
(2) Touch switches 12×12×4.3 (24pcs)
(3) PS2 keyboard interface
(4) Independent keyboard interface
(5) 4×4 rectangular keyboard interface
(6) Module size: 290mm×150mm×150mm
8. ADC/DAC module
(1) DAC0832
(2) ADC0809
(3) 0-5V analog voltage source
(4) 8-grade LED level indication
(5) Active clock generator
(6) Module size: 290mm×150mm×150mm
9. AC/DC motor control module
(1) Permanent magnet synchronous motor
(2) DC gear motor
(3) DC5V relays
(4) Signal plates
(5) Photoelectric counter
(6) Module size: 290mm×150mm×150mm
10. Stepping motor control module
(1) Scale
(2) Stepping motor with driver
(3) DC5V relay
(4) Sensors
(5) Motor gear with belt
(6) Module size: 290mm×150mm×150mm
11. Sensor adapter module
(1) 8-bit optocoupler (2 groups)
(2) Four-way sensor interfaces
(3) Connecting terminals
(4) Module size: 290mm×150mm×150mm
12. Extended module
(1) Chip 8255
(2) Chip 74LS245
(3) Extended port wiring leads
(4) 5V power supply with indicator
(5) Module size: 290mm×150mm×150mm
13. Temperature sensor module
(1) Analog temperature sensor LM35
(2) Digital temperature sensor 18B20
(3) DC12V relays
(4) 12V/5V power supply
(5) Resistors
(6) Module size: 290mm×150mm×150mm
14. Nixie Tube Display Module
(1) Dot matrix nixie tube module 8pcs
(2) Common anode nixie tube 8pcs
(3) ON/OFF switch
(4) LED indicators
(5) 5V power supply
(6) Module size: 290mm×150mm×150mm
15. Accessories
(1). Digital multimeter
(2). RS232 communication cable
(3). ISP programming unit
(4). Flat cable suite
(5). Electronic connecting wire suite
(6). Safety connecting wire suite
(7). CD (sample, programming, simulation) (1pcs)
(8). Guide book (1pcs)
7 Motor & Transformer Maintenance & Test Training System Digunakan untuk pembelajaran mengenai motor listrik dan transformator, antara lain : melepas lilitan motor, menggulung ulang, merakit, analisa data, dan keterampilan lain mengenai transformator 1PH, motor induksi 1PH, motor induksi 3PH, dan sebagainya. CHOIEO 66962605 1 168.000.000
Features :
• This trainer is designed with three phase AC adjustable power supply, DC power supply and AC/DC measuring meters. Meanwhile, dedicated disassembling tools are adopted such as motor wire embedding tools, hand operated digital winding machine, etc.
• It is ideal for students to conduct training of single phase transformer, single phase motor and three phase motor, including disassembly, rewind, assembly, short-circuit test, no-load test, breakdown maintenance, etc.
EXPERIMENTS
• Single phase transformer maintenance and test
• Single phase motor maintenance and test
• Three phase asynchronous motor maintenance and test
• DC motor maintenance and test
TECHNICAL PARAMETERS
1. Working power supply: three phase five-wire AC 380V ±5%, 50Hz
2. Safety protection: leakage protection (action current ≤ 30mA), overcurrent protection, fuse protection.
3. Rated power: ≤ 1.1KW 3. Environment temperature: -10°C~+40°C
4. Dimension :1500mm×750mm×1400mm (approx.) 5. Relative humidity: ≤90% (25°C) > BASIC CONFIGURATION
1. Personal safety protection:
(1) The three phase power input is designed with current mode residual-current circuit breaker
(2) The three phase adjustable power output is designed with current protection function, with current transformer for experiment current detection, it can cut off the power when overcurrent appears.
(3) Both DC power and AC/DC instruments are designed with outrange alarm and general power cut off function, which can protect device effectively.
(4) Whole sealing gun type plug-in connecting wires are adopted for experiment connection, the inner core is made of oxygen free copper 128 strand wire and the plug is made of solid copper. The metal part is shielded to avoid electric shock.
2. Power part:
(1) Single phase / Three phase adjustable power supply: Provided with 0~450V three phase adjustable AC power supply (with a three phase autoformer regulator), which can be switched by switch. It has three phase output voltage monitoring function, when the short circuit happens or the current reaches 5A, it can automatically trip and alarm.
(2) DC stabilized power supply: Adjustable range 0~250V, maximum output current 1A, 3 1/2 bit digital display, with short circuit protection and self-recovery function.
3. Measuring instruments:
(1) Digital DC voltmeter 0~300V, three levels (2/ 200/300V), switched by key switch, precision class 0.5, 3 1/2 bit digital display.
(2) Digital DC milliammeter 0~2000mA
(3) Digital AC voltmeter: 0~500V, precision class 0.5
(4) Digital AC ammeter: 0~5A, precision class 0.5
(5) Digital power factor meter: 0~500V, 0~5A, precision class 1.0
Motor and Transformer
1. Transformer (220V without dipping paint)
2. Single phase motor (220V, 180W without dipping paint)
3. Three phase motor (180W without dipping paint)
4. Separately excited DC motor (220V, 180W)
8 Analog Circuit Training Kit Digunakan sebagai perangkat untuk pelatihan tentang rangkaian analog. CHOIEO 66968305A 1 78.028.500
TRAINING CONTENT
Analog Electronics Part
• Usage of commonly used instrument
• Diode characteristic test
• Triode transistor input, output characteristics test
• Transistor single transistor amplifier
• Two-pole amplifier circuit
• Negative feedback amplifier circuit
• Emitter follower
• Field-effect tube amplifier circuit
• Differential amplification circuit
• RC sine wave oscillator
• LC sine wave oscillator
• Operational amplifier parameter testing
• Integrated operational amplifier proportional summation operational circuit
• Integrated operational amplifier integrating and differentiating circuit
• Integrated operational amplifier voltage comparator circuit
• Integrated operational amplifier waveform generator circuit
• Integrated operational amplifier active filter circuit
• Integrated power amplifier
• OTL power amplifier
• Integrated voltage stabilizer
• Series voltage stabilizing circuit
PRODUCT COMPOSITION
1. Dimension: 1500mm×700mm×1600mm (approx.)
2. Working power supply: 220V/50Hz
3. Safety protection: Current mode residual-current circuit breaker, voltage mode leakage protector
4. Training table: Steel and wood structure, iron spraying plastics, wearproof and fireproof panel, equipped with drawer and cabinet for the storage of tools and components. (or aluminum alloy structure optional)
5. Analog circuit experiment part:
(1). Adjustable DC stabilized power supply: 0~30V/1.5A continuously adjustable, automatic shifting, with automatic overload protection and self-recovery function.
(2). Fixed DC stabilized power supply: +5V/3A, ±12V/1A
(3). AC power supply: 18V, 9V, 3V, 0V
(4). Function signal generator: wave form (sine wave, triangular wave, square wave), frequency range: 5Hz~550KHz continuously adjustable, output amplitude: sine wave more than 0-10Vp-p
(5). Frequency meter: measurement range: 1Hz~8MHz, 6-bit digital display, automatic shifting, input impedance ≥1MΩ/20PF, sensitivity
Measuring meter:
(1). Voltmeter: DC200V, class 0.5
(2). Ammeter: DC200mA, class 0.5
(3). Digital multimeter
9 Digital Circuit Training Kit Digunakan sebagai perangkat untuk pelatihan tentang rangkaian digital CHOIEO 66968305A 1 78.028.500
TRAINING CONTENT
Analog Electronics Part
• Usage of commonly used instrument
• Diode characteristic test
• Triode transistor input, output characteristics test
• Transistor single transistor amplifier
• Two-pole amplifier circuit
• Negative feedback amplifier circuit
• Emitter follower
• Field-effect tube amplifier circuit
• Differential amplification circuit
• RC sine wave oscillator
• LC sine wave oscillator
• Operational amplifier parameter testing
• Integrated operational amplifier proportional summation operational circuit
• Integrated operational amplifier integrating and differentiating circuit
• Integrated operational amplifier voltage comparator circuit
• Integrated operational amplifier waveform generator circuit
• Integrated operational amplifier active filter circuit
• Integrated power amplifier
• OTL power amplifier
• Integrated voltage stabilizer
• Series voltage stabilizing circuit
PRODUCT COMPOSITION
1. Dimension: 1500mm×700mm×1600mm (approx.)
2. Working power supply: 220V/50Hz
3. Safety protection: Current mode residual-current circuit breaker, voltage mode leakage protector
4. Training table: Steel and wood structure, iron spraying plastics, wearproof and fireproof panel, equipped with drawer and cabinet for the storage of tools and components. (or aluminum alloy structure optional)
5. Analog circuit experiment part:
(1). Adjustable DC stabilized power supply: 0~30V/1.5A continuously adjustable, automatic shifting, with automatic overload protection and self-recovery function.
(2). Fixed DC stabilized power supply: +5V/3A, ±12V/1A
(3). AC power supply: 18V, 9V, 3V, 0V
(4). Function signal generator: wave form (sine wave, triangular wave, square wave), frequency range: 5Hz~550KHz continuously adjustable, output amplitude: sine wave more than 0-10Vp-p
(5). Frequency meter: measurement range: 1Hz~8MHz, 6-bit digital display, automatic shifting, input impedance ≥1MΩ/20PF, sensitivity
Measuring meter:
(1). Voltmeter: DC200V, class 0.5
(2). Ammeter: DC200mA, class 0.5
(3). Digital multimeter
10 Programmable Logic Controller Training Set Digunakan sebagai perangkat untuk pelatihan penggunaan Programmable Logic Control (PLC). CHOIEO 66965101 1 112.602.000
Features :
• This trainer is suitable for courses such as 'PLC Technology', , 'Electric Appliance and PLC Control Technology' and 'PLC Application'.
• It is mainly composed of control panel, PLC mainframe, modular simulation modules and so on.
• The training table adopts plastic sprayed steel structure and designed with drawer, which is convenient for the storage of tools and modules. The table top is made up of high density board, with fireproof, waterproof and wearproof function.
• Frequency converter and motor can be added to extend the experiment content when needed. (optional)
• Safety protections: grounded, lead protection, safety in accordance with related GB standards. Insulated safety sockets, sheathed cables and wires.
TRAINING CONTENT
• PLC basic instruction training
• Motor forward and reverse control simulation
• Television transmitting tower simulation
• Traffic light control system simulation
• Automatic goods delivery and loading system simulation
• Automatic water tower water level control simulation
• Automatic molding machine system simulation
• Various liquids automatic control system simulation
• Automatic punching machine control system simulation
• Elevator control system simulation
• Automatic mail sorting system simulation
• Automatic washing machine control system simulation
• Plating control system simulation
• Automatic vending machine system simulation
• Relay control experiment
• Software simulation control
TECHNICAL PARAMETER
1. Input Voltage : AC 380V/220v, 50Hz 2. Temperature : -5~40°C, Below RH 90% 3. Overall power consumption: 0.3 kVA 4. Dimensions: table 1575mm×680mm×835mm (approx.) bench 1130mm×250mm×720mm (approx.) >BASIC CONFIGURATION 1. Training table: it adopts steel-wood material, with 16mm medium density fiberboard as the tabletop. The frame is made of rectangular steel tubes. The structure is designed with two drawers, PC cabinet, keyboard tray and lockable universal wheels.
2. Round stool (2pcs): Screw lifting range: 450~500mm, seat size: 300mm×300mm (approx.)
3. Control panel:
(1) AC power control unit: It is equipped with lighted fuse and leakage protection switch and provided with three phase 380V and single phase 220V power supply (one group each), which can be controlled by start-stop switches. Three-phase-four-wire AC 380V supply via air switch and can be monitored by voltmeter.
(2) Timer and alarm recorder: It has time setting, timing alarm, power cut-off function and can automatically record the electric leakage alarm time, which is caused by connection or operation.
(3) DC stabilized voltage: 0~30V adjustable, with rough/accurate adjust rotary knobs.
(4) DC constant current source: 0~200mA adjustable, with rough/accurate adjust rotary knobs.
(5) DC digital voltmeter: 0~200V, 10MΩ, class 0.5
(6) DC digital ammeter: 0~200mA, class 0.5
(7) Logic level output and indicator, self-locking/jog buttons
(8) Programmable logic controller: FX1N-40MR, 24I/16O, relay output
4. PLC simulation module (standard modular dimension 150mm×288mm×50mm)
(1) Motor positive and negative rotation control
(2) Television transmitting tower
(3) Traffic light control system
(4) Automatic goods delivery and loading system
(5) Automatic water tower water level control
(6) Automatic molding machine system
(7) Various liquids automatic control system
(8) Automatic punching machine control system
(9) Elevator control system
(10) Automatic mail sorting system
(11) Automatic washing machine control system
(12) Plating control system
(13) Automatic vending machine system
(14) Relay control experiment
5. Experiment wire: Length: 40cm/60cm/100cm, red/yellow/black, 60pcs in total.
6. PLC Programming software(copy): GX-Developer, It can accomplish the edit of PLC ladder diagram, instruction list, SFC,etc. The program can be saved as GPPQ, GPPA format.
7. Programmable cable: USB2.0 PC port, round head 8-pin PLC port, with 3 color LED communication indicator and driver disc (one-button type installation, available for windows XP, VISTA, WIN7, etc.).
8. Simulation software (copy): GX simulator.
9. PLC program: Programs for 14 simulation modules, 27 basic instructions, advanced instruction application
10. Power socket
Instruction module, Power adapter module, Test line, CD, Download line, User Manual.
11 Basic Electro Pneumatic Training System Digunakan sebagai perangkat untuk pelatihan elektro pneumatik dasar. CHOIEO 66971105 1 195.000.000
Features :
• The electro pneumatic training platform is made up of experimental table, frame, pneumatic components, electrical control modules and so on.
• Modular structure design is adopted for experiment construction, each pneumatic component is an independent unit that comes with mounting baseboard. Reliable quick connectors are used for the connection of components.
• Aluminum alloy profile panel, with ‘T’ type mounting slot for pneumatic components installation and circuit construction. All solenoid valves, sensors and mircoswitches are designed with 4mm safety plug sockets for quick connection.
• The air compressor adopts air oil-less type compressor, which has the advantage of light weight, low power consumption and low noise.
• Safety protections: grounded, lead protection, safety in accordance with related GB standards. Insulated safety sockets, sheathed cables and wires.
TRAINING CONTENT
• Understanding of pneumatic structure and components
• Single acting cylinder manual reversing controlled loop
• 5/3 way solenoid directional valve controlled single acting cylinder loop
• 5/2 way single solenoid directional valve controlled single acting cylinder loop
• 5/2 way double solenoid directional valve controlled single acting cylinder loop
• Double acting cylinder hand directional valve control loop
• Double acting cylinder 5/2 way single solenoid directional valve control loop
• Double acting cylinder 5/2 way double solenoid directional valve control loop
• Single acting cylinder inching control loop
• Double acting cylinder inching control loop
• Sensor (capacitive/ photoelectric/ inductive) application control loop
• Dual pressure valve control loop
• Quick exhaust valve application control loop
• Sequence valve application control loop
• Time delay valve application control loop
• Four-cylinder linked action loop
• Double acting cylinder one-way speed regulation loop
• Double acting cylinder both-way speed regulation loop
TECHNICAL PARAMETERS
1. AC power input: single phase AC220V±10%, 50Hz, 10A
2. Environment temperature: -10ºC~40 ºC Ambient humidity ≤ 85% (25 ºC)
3. Overall consumption: ≤ 2KVA
4. Working power supply: DC24V, 4.5A with short circuit protection function
5. Dimension: 1300mm×600mm×1700mm
6. Aluminum plate:1200mm×735mm (approx.)
PNEUMATIC COMPONENTS
1. Single acting cylinder (spring return) (Qty:1)
2. Double acting cylinder (Qty:3)
3. Air service unit (reduce valve/lubricator/filter) (Qty:1)
4. Reduce valve with pressure gage (Qty:1)
5. (5/2way) single solenoid valve (Qty:2)
6. (5/2way) double solenoid valve (Qty:1)
7. (5/2way) hand directional valve (Qty:1)
8. (3/2way) solenoid valve (Qty:1)
9. Air on/off valve (Qty:1)
10. (5/2way) double pneumatic valve (Qty:2)
11. (5/2way) single pneumatic valve (Qty:2)
12. Sequence valve (Qty:1)
13. Rotary cylinder (Qty:1)
14. Shuttle valve (Qty:2)
15. Dual pressure valve (Qty:1)
16. Time delay valve (Qty:1)
17. Quick exhaust valve (Qty:1)
18. One way valve (Qty:2)
19. Button valve (Qty:1)
20. Rotary valve (Qty:1)
21. Stroke valve (Qty:1)
22. Mushroom head button valve (Qty:1)
23. Throttle valve (Qty:6)
24. Capacitive sensor (Qty:4)
25. Photoelectric sensor (Qty:4)
26. Inductive sensor (Qty:4)
27. Magnetic reed switch suite (for cylinder) (Qty:1)
28. Microswitch (left trigger) (Qty:2)
29. Microswitch (right trigger) (Qty:2)
ELECTRICAL CONTROL
1. Control panel board
(1) High brightness aluminum-plastic panel
(2) Size: 1200mm×735mm
2. Power part
(1) Six way DC 24V
(2) Three way single phase AC220V
(3) Leakage protective switch, emergency stop button, key on/off switch, main power indicator
3. Inching buttons
(1) 1NC/1NO inching button: 1 red, 2 green
(2) 1NO inching button: green
4. Self-locking rotary knobs: 1NC/1NO, two groups
5. Indicating light: 1 red, 1 green with connecting sockets
6. Relay part
(1) 3NO/3NC relay: 5-fold, with led indicators
(2) 1 timer relay, adjustable with delayed pick-up
(3) 1 timer relay, adjustable with delayed release
ACCESSORIES
1. T-joint (Qty:10)
2. Cross joint (Qty:10)
3. Y-joint (Qty:10)
4. Air tube suite (Qty:1)
5. Tube plug (Qty:20)
6. Mounting base (Qty:5)
7. Air compressor:
(1) Motor power: 550W
(2) Rated current: 2.8A
(3) Input voltage: 220V, 50Hz
(4) Speed: 1380r/min
(5) Flow: 40L/min
(6) Capacity: 30L 8. Tools: straight screwdriver, scissors, nipper pliers, cross screwdriver, monkey wrench, sealing tape, socket head wrench
12 Basic Electro Hydraulic Training System SSEDU ZMH-1107 1 540.000.000
13 Mesin Bubut Konvensional Untuk pengenalan dan pelatihan pengerjaan benda kerja menggunakan mesin bubut konvensional RICHON CZ-1440G/1 1 207.759.000
Features :
Supersonic frequency hardened bed ways
Precision roller bearing for spindle
High quality steel, ground and hardened gear inside headstock
Easy and fast operating gearbox
Enough strong power motor
ASA D4 camlock spindle nose
Various threads cutting functions available
Technical Data
Swing over bed mm φ355,Swing over carriage mm φ220
Swing over gap mm φ500,Width of bed-way mm 186
Distance between centers mm 1000,Taper of spindle M.T.5
Spindle diameter mm φ38,Step of speed 8
Range of speed rpm 70~2000,Head D1-4
Metric thread 26kinds (0.4~7mm),Inch thread 34kinds(4~56T.P.I)
Moulder thread 16 kinds(0.35~5M.P),Diametral thread 36 kinds(6~104D.P)
Longitudinal feeds mm/r 0.052~1.392 (0.002”~0.0548”)
Cross feeds mm/r 0.014~0.38 (0.00055”~0.015”)
Diameter of lead screw mm φ22(7/8”)
Pitch of lead screw 3mm or 8T.P.I
Saddle travel mm 1000,Cross travel mm 170,Compound travel mm 74
Barrel travel mm 95,Barrel diameter mm φ32,Taper of center mm M.T.3
Motor power Kw 1.5(2HP),Motor for coolant system’s power Kw 0.04(0.055HP)
approx. Machine(L×W×H) mm 1920×750×760,Stand(left) (L×W×H) mm 440×410×700
approx. Stand(right) (L×W×H) mm 370×410×700
approx. Machine Kg 505/565,Stand Kg 70/75
Standard accessories:
Three jaw chuck,Four jaw chuck,Steady rest,Follow rest,Lathe stand
Center,Center sleeve,Change gear,Oil gun,Working light,Coolant system
Foot brake,Tools and tool box
14 Pipe Thread Machine Untuk mengenalkan dan memberi keterampilan membuat ulir pada pipa menggunakan pipe thread machine BOL ZIT-R2 1 19.032.000
Specifications:
Pipe capacity: 1/2"-2"
Bolt capacity: M12-M33
Conduit capacity: C15,C19-31,C39-51(optional, Die for conduit is not standard accessories)
Applicable threader standards: BSPT,NPT, BSPP,BSW,Metric (need to exchange additional Die)
Power: 750W
Speed: 28 RPM
Voltage: 220V~ or 110~ single phase
Frequency: 50Hz or 60Hz
Switches FOR/OFF and safety foot switch optional
Die: Alloy or HSS
Cutter: Wheel type, self-centering
Reamer: 1/2"-2" cone blade, 5-flute cone optional
Oil pump: Gerotor Oil Pump
Gross/net weight: 85/73Kg
Packing size: 720x480x560mm
Standard Accessories
Two manual type Die Head
One set of 1/2”-3/4” Die
One set of 1”-2” Die
One set of M12 Die
One set of M14-M16 Die
One set of M18-M22 Die
One set of M24-M27 Die
One set of M30-M33 Die
One set of 1/2"-2"Cutter Kit
One set of 1/2"-2"Reamer Kit
Three pcs of Tubular Supporter
15 Gerinda Listrik Tangan Untuk mengenalkan dan memberi keterampilan menggerinda atau menghaluskan permukaan benda kerja menggunakan mesin gerinda tangan HIKOKI G 10SS 1 1.800.000
Specifications
Capacity: Wheel Dia 100mm (4")
Capacity: Hole Dia 16mm (5/8")
Spindle Thread M10 x 1.5
Power Input 600W ~ 650W
No Load Speed 11,500/min. : 220-240V
12,000/min. : 110-120V
Overall Length 254mm (10")
Weight*3 1.7kg (3.8lbs.)
Standard Accessories Side Handle, Wrench
16 Mesin Gerinda Potong Untuk mengenalkan dan memberi keterampilan memotong bahan baku produk menggunakan mesin gerinda potong. HIKOKI CC14SST/STD 1 6.097.500
Features :
Power input 2,200W
Quick lock vise
Spark diversion guard
Spindle lock
Specifications
Capacity:Cut-off Wheel Dia. 355mm (14")
Power Input 2,200W
No Load Speed 3,800/min.
Max Workng Perphera Speed 4,800m/min.
Dimensions (L x W x H) 590 x 300 x 640mm (23-7/32" x 11-13/16" x 25-3/16")
Weight 17.0kg (37.4 lbs.)
Standard Accessories Cut-off Wheel, Wrench
Round pipe approx. 115mm/Square approx. 115x115mm/Rectangle approx. 150x102mm
17 Digital optical measurement profile projector Untuk alat ukur komponen yang relatif kecil. SINPO JT-300 1 296.250.000
Features:
-The up and down system adopts linear guide way and nuts without interference. It's more comfortable and stable.
-The reflecting mirror adopts patent coating techniques with good anti-dust effects.
-The transmission illumination has high and low levels, which can meet different measuring requirements.
-Light source adopts Philip tungsten halogen lamp with high brightness and long using life to satisfy long time using demands.
-Axial flow fan with strong dissipations heat function dissipates heat in double directions
-The optical system has excellent quality, the objective forms clear image and the magnification is accurate.
-The working distance on object is large, which can meet measuring requirements of different parts.
-The RS232 port can realize the output and communication of data with computer.
- It is erect image with external DRO which is according to the operator's habits.
Technical parameters:
-Screen Diameter: Φ300mm
-Rotating range: 0°~360°
-Resolution of the rotary angle: 1
-Accuracy of the rotary angle: 6
-Objective
Magnification Object Visual Field (mm) Object Working Distance (mm)
10X φ30 75.201
20X φ15 69.599
50X φ6 44.4
100X φ3 26.243
DS600 or DS401 Box
-Errorof magnifying power ≤ 0.08%
-Worktable area: 400×225mm
-Travel of workstage: X=200mm Y=100mm Z=90mm
-Display equivalent of X Y: 1μm
-Accuracy of instrument: (3+L/75) um, L unit: Mm
-Load capability of worktable: 5kg
-Lighting source
Transmission lighting: 12V 100W Halogen tungsten lamp
Reflecting lighting: 24V 150W Halogen tungsten lamp
-Overall sizes of the instrument (mm): 694×380×1065
-Machine Weight: 135 kg
-Ambient environment of the instrument service
-Working temperature: 20±5'C
-Relative humidity: Not more than 60%
18 Power Block Merupakan mesin bantu yang digunakan untuk menarik jaring pukat cincin dari dalam air ke atas deck kapal, bisa bertenaga hidrolik maupun listrik. KERNEL HHXG-KA2 1 30.000.000
Technical Data
Rated load(kg) 2000
Load Chain(mm×mm) φ8×24
Handle Control Voltage(V.AC) 24
Power(KW) 1.1
Lifting height(m) 3
Lifting speed(m/min) 2.5
Work Rate S3-30% 20 min
Rated Volt(V) 220 V 50 Hz
Packing Size(mm) 690×410×470
N.w(kg) 54
19 Manual Shearing Machine Untuk mengenalkan dan memberi keterampilan memotong lembaran plat menggunakan manual shearing machine. RICHON Q01-1.5X1320 1 77.962.500
Product Description
The shearing machine with both front and back gauge
Used for mild steel aluminum copper, brass zinc plastic and leads
Features:
The Manual shear is with both front and back gauge
With heavier weight, good stability
High carbon and chrome steel blade
A fully casting structure, not easy deformation
Used for mild steel aluminum copper, brass zinc plastic and leads
It features convenient operation and high efficiency.
Technical Data
Width (mm) 1320
Length (mm) 1500
Max. Shearing thickness (mm) 1:05
Back gauge range (mm) 0-700
Packing size (cm) 168x76x115
N.W./G.W. (kg) 491/545
20 Band Saw Machine Untuk mengenalkan dan memberi keterampilan memotong bahan baku produksi menggunakan band saw machine. RICHON BS-912B 1 85.800.000
Main features:
Adjustable hydraulic feed cutting rate for multiple applications
Mitre cuts to 45º using calibrated vice
Built-in coolant system to both blade guides for maximum cutting efficiency
Limit switch stops machine when cut is complete
Quick action material clamping lever
Adjustable blade roller guides provides accurate cutting
Adjustable 4-speed pulley drive system enabling 26-50-73-95mpm cutting speeds
Adjustable length stop for repetition cutting
Wire wheel brush to clean swarf from blade
Portable - on wheels for ease of use
Automatic electric cut-out switch
Technical Data
Capacity
Circular @90° mm/'' 229(9)
Rectangular @90° mm/'' 178×305(7×12)
Circular @45° mm/'' 150(6)
Rectangular @45° mm/'' 127×150(5×6)
Blade speed @50HZ MPM
@60HZ MPM 26,50,73,95
Blade size mm 27×0.9×2655
Motor power W/HP 1100/1500 ~ 2.0/1.0
Drive . V-belt
Packing size cm 154×59×115
N.W./G.W. kg 230/260
21 MMA Welding Machine Untuk mengenalkan dan memberi keterampilan mengelas menggunakan las MMA. TOPWELL STICK-200HD 1 13.275.000
Technical specifications
Rated Input Voltage 1PH ~ 230V ±15%
Max. Load Power Capacity 8.75 KVA ~ 14KVA
Rated Duty Cycle(40℃) 60% 200A/28V
100% 180A/27.2V
Welding Current/Voltage Range 20A/20.8V~200A/28V
Open Circuit Voltage 70V~80V
Power Factor 0:08
Efficiency 80%
MMA Arc Force Preset
Hot Start Time Preset
Hot Start Current Preset
Dimension 345X145X230mm
Weight 4.6KG
22 MIG-MMA Welding Machine Untuk mengenalkan dan memberi keterampilan mengelas menggunakan las MIG. TOPWELL MIG-200Di 1 19.492.500
Technical specifications
Rated Input Voltage 1PH ~ 230V ±15%
Max. Load Power Capacity 8.75KVA
Rated Duty Cycle(40℃) 35% MIG: 200A/24V
MMA: 200A/28V
TIG: 200A/18V
100% MIG: 160A/22V
MMA: 160A/26.4V
TIG: 160A/16.4V
Welding Current/Voltage Range MIG: 10A/14.5V ~200A/24V
MMA: 20A/20.8V~200A/28V
TIG: 5A/10.2V~200A/18V
Open Circuit Voltage 70V~80V
Power Factor 0:08
Efficiency 80%
Pre-Gas Time Preset
Flow-Gas Time Preset
Wire-feed Mechanism 2 Rollers
Wire-feed Speed Range 2-18m/min
Wire Spool Capacity 200mm (5kg)
Filler Wires Ø (mm) Fe, Ss 0.6~1.0 mm
Dimension: 490x230x385mm
Weight 20KG
23 TIG Welding Machine Untuk mengenalkan dan memberi keterampilan mengelas menggunakan las TIG. TOPWELL Alutig-200P 1 35.100.000
Technical specifications
Rated Input Voltage 1PH ~ 115/230V ±15%
Max. Load Power Capacity TIG:5.63KVA
MMA:6.60KVA
Rated Duty Cycle(40℃) 60% TIG: 200A/18V
MMA: 160A/26.4V
100% TIG: 160A/16.4V
MMA: 130A/25.2V
Welding Current/Voltage Range TIG: 5A/10.2V~200A/18V
MMA: 20A/20.8V~160A/26.4V
Open Circuit Voltage 70V~80V
Power Factor 0,06875
Efficiency 80%
TIG Pulse Peak Current
Pulse Frequency 0.2Hz~200Hz
Pulse Width (Ratio) 1~100%
AC TIG AC Frequency Range 20Hz~250Hz
AC Clean Width (AC Balance) +40~-40
AC Clean Ratio (AC Bias) % +30~-50
MIX TIG MIX Frequency: 1Hz~5Hz
DC Balance: (%) 20~80
Arc-starting Current 5A~250A
Crater-filling Current 5A~250A
Current Up-slope Time 0.1S~15S
Current Down-slop Time 0.1S~15S
Pre-Gas Time 0.1S~15S
Flow-Gas Time 0.1S~15S
Spot Arc Time 0.1S-10S
MMA Arc Force 10A~160A
Hot Start Time 0.1~3S
Hot Start Current 10A~160A
Dimension (LxWxH) 540x240x480mm
Weight (KG) 23KG
24 Plasma Cutting Welding Machine Untuk mengenalkan dan memberi keterampilan mengelas menggunakan las plasma. TOPWELL CUT-60Di 1 50.775.000
Technical specifications
Item No CUT-60Di
Input voltages (±15%) 200–240V, 1-PH, 50-60Hz
Max Input current 200/240V, 48/40A
Output current 30-60A
Rated output voltage 104V
Duty cycle @ 40° C (104° F) 60% @60A
100% @40A
Open circuit voltage (OCV) 280V
Dimensions 540x240x480mm
Weight 19kg
Gas supply Air (clean, dry and oil-free)
Recommended gas inlet flow rate/pressure 0.3-0.5Mpa
Power supply type Inverter – IGBT
Electrical efficiency 80%
Max. Load Power Capacity 9.7KVA
Certifications CE, RoHS
Warranty Power supply: 3-year
Torch: 1-year
25 Hand Tool Set Technical Data : KERNEL W2163 1 12.150.000
1 piece Tricolor handle very long “one” word screwdriver 6 * 250mm
1 piece Tricolor handle very long Cross Screwdriver PH2 * 250mm
1 piece Tricolor handle very long Cross Screwdriver PH1 * 250mm
1 piece color handle clock ”one” word screwdriver 1.4 * 60mm
A piece of two-color handle clock ”one” word screwdriver 1.8 * 60mm
A piece of two-color handle clock ”one” word screwdriver 2.5 * 60mm
A piece of double color handle clock ”one” word screwdriver 3.0 * 60mm
1 piece color handle clock cross screwdriver PH00 * 60mm
1 piece double color handle clock cross screwdriver PH0 * 60mm
1 piece 6.3mm series rotary handle
1 piece 6.3mm series screwdriver change head
20 pieces batch head
1 piece double-colored needle mouth pliers 6 inch
1 piece double-colored diagonal bevel pliers 6 inch
1 piece of olecranon wire stripper
1 piece network crimping pliers 6P8P
9 pieces metric strong sleeve
1 piece automatic range digital multimeter
1 piece electric iron 30W (CCC certification)
1 piece of solder wire 10g
1 piece gold aluminum suction tin
1 piece pointed tweezers
1 piece curved blade electrician
9 pieces metric folding internal hexagon
1 piece hand saw 10 inches
1 piece digital display pen
1 piece of insulation tape 9M
1 piece working headlight
26 Electric Drill Technical Data HIKOKI DV10VST 1 2.250.000
Chuck Capacity 10mm (3/8")
Capacity: Steel 10mm (3/8")
Capacity: Wood 25mm (1")
Power Input 450W
No Load Speed 0 - 3,200/min.
Overall Length (with Keyed Chuck) 227mm (8-15/16")
Overall Height (with Keyless Chuck) 176mm(6-15/16")
Weight (with Keyed Chuck) 1.2kg (2.6lbs.)
Standard Accessories Chuck Wrench
Torque set: 23+1
Max torque force: approx. 35N.m
27 Impact Drill Kit Features : FIXTEC FID600K50 1 2.250.000
600w Impact Drill kit with 50pcs accessories
Tackle tough jobs with the impact drill kit with 50pcs accessories from Power Tools.
A switch lets you set the tool to operate as a traditional drill or a hammer drill with a hammering action.
A detachable side-assist handle offers greater control, as does the two-finger, variable-speed precision trigger.
Technical Data
Model Number
Voltage/Frequency 230v/50Hz
Input power 600W
Chuck size 13mm
No-load speed 0-3000rpm
Reversible Yes
Max impact rate 48000bpm
Drilling capacity:
steel: approx. 13mm/ concrete: approx. 13mm/ wood: approx. 25mm With 50pcs accessories
28 Rotary Hammer Technical Data FIXTEC FRH85001 1 3.300.000
Voltage 220-240V ~ 50-60Hz
Rated power 850W
No load speed 900rpm
Impact rate 4000bpm
Impact energy per stroke 5.0J
Tool holder SDS-PLUS
Max. drilling dia.
- Steel 13mm
- Wood 42mm
- concrete 26mm
Weight 4.6KG
Protection class II
Impact Joules: 5J Drilling capacity:
steel: approx. 13mm/ concrete: approx. 26mm/ wood: approx. 42mm Accessories:
29 Multi-function Tools Specifications and Features OSTAR MT400-01 1 2.340.000
Volt: 230~240V/50Hz
No-load Oscillation Speed: 11000~20000RPM/min
Oscillation Angle: 4.5 Degree
Power: 400W(VDE)
Machine Weight: 1.3 kg
Packing: BMC+Brown Box
Regular Accessories:
1X scraper/Straight Cut Blade /sanding pad,3pcs sanding paper
Main Feature:
* Quite Light +Best Blance+Variable Speed Control
* Slim Body + Comfortable Soft Grip
30 Drill Press Specifications : KERNEL ZHX-13 1 17.700.000
Maximum Drilling Capacity 13 mm
Diameter of Column 46 mm
Spindle Travel 50 mm
Distance Spindle Axis to Column Generating Line 103 mm
Max. Distance Spindle Nose to Table 220 mm
Max. Distance Spindle Nose to Base 300 mm
Spindle Taper B16
Spindle Speed Range 515-2580 rpm
Spindle Speed Series 5
Dimension of Worktable Surface 160x160 mm
Dimension of Base 280x180 mm
Overall Height 580 mm
Power of Motor 180W
Voltage 220V
Gross / Net Weight 21/19 kg
Packing Dimension 460Hx330Lx230W mm
Kompetensi Keahlian Teknika Kapal Niaga
No Nama Alat Merk Tipe Qty Harga Satuan
1 Engine Room Simulator TRANSAS 1 30.000.000.000
2 Motor Diesel DEUTZ MB-DY200 1 1.177.789.500
3 Motor Bensin PARSUN F40BWS-T-EFI 1 235.500.000
4 Insatalasi Poros Baling-baling -
5 Basic Electronics Trainer SSEDU ZE1110 1 31.719.000
6 MCU Training Set CHOIEO 66968201 1 138.000.000
7 Motor & Transformer Maintenance & Test Training System CHOIEO 66962605 1 168.000.000
8 Analog Circuit Training Kit CHOIEO 66968305A 1 78.028.500
9 Digital Circuit Training Kit CHOIEO 66968305B 1 78.028.500
10 Programmable Logic Controller Training Set CHOIEO 66965101 1 112.602.000
11 Basic Electro Pneumatic Training System CHOIEO 66971105 1 195.000.000
12 Basic Electro Hydraulic Training System SSEDU ZMH-1107 1 540.000.000
13 Mesin Bubut Konvensional RICHON CZ-1440G/1 1 207.759.000
14 Pipe Thread Machine BOL ZIT-R2 1 19.032.000
15 Gerinda Listrik Tangan HIKOKI G 10SS 1 1.800.000
16 Mesin Gerinda Potong HIKOKI CC14SST/STD 1 6.097.500
17 Digital optical measurement profile projector SINPO JT-300 1 296.250.000
18 Power Block KERNEL HHXG-KA2 1 30.000.000
19 Manual Shearing Machine RICHON Q01-1.5X1320 1 77.962.500
20 Band Saw Machine RICHON BS-912B 1 85.800.000
21 MMA Welding Machine TOPWELL STICK-200HD 1 13.275.000
22 MIG-MMA Welding Machine TOPWELL MIG-200Di 1 19.492.500
23 TIG Welding Machine TOPWELL Alutig-200P 1 35.100.000
24 Plasma Cutting Welding Machine TOPWELL CUT-60Di 1 50.775.000
25 Hand Tool Set KERNEL W2163 1 12.150.000
26 Electric Drill HIKOKI DV10VST 1 2.250.000
27 Impact Drill Kit FIXTEC FID600K50 1 2.250.000
28 Rotary Hammer FIXTEC FRH85001 1 3.300.000
29 Multi-function Tools OSTAR MT400-01 1 2.340.000
30 Drill Press KERNEL ZHX-13 1 17.700.000
Untuk
pemesanan atau informasi silahkan hubungi alamat kontak kami :
CV.ASAKA PRIMA | DUTA MEDIA GROUP.
PERCETAKAN & DISTRIBUTOR ALAT LAB & PERAGA PENDIDIKAN.
Jl.Maulana Hasanudin No.52 Cipondoh - Kota Tangerang
PERCETAKAN & DISTRIBUTOR ALAT LAB & PERAGA PENDIDIKAN.
Jl.Maulana Hasanudin No.52 Cipondoh - Kota Tangerang
Cabang : Ruko Pondok Permata No.1, Jl.
Raya Tanggul, Rajeg Mulya, Rajeg, Tangerang, Banten 15540
021 5570 1397
021 5570 2265
0813.1019.7873
WA.0812.1236.8589
WA.0877.7432.4146
0813.8053.7399
www.asakaprima.net
asakaprima@gmail.com
021 5570 1397
021 5570 2265
0813.1019.7873
WA.0812.1236.8589
WA.0877.7432.4146
0813.8053.7399
www.asakaprima.net
asakaprima@gmail.com